Honda CBX Pro Fault Codes
Honda CBX Pro motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following honda cbx pro faults are the list of some of the parts of a motorcycle engine.
We’ve compiled a list of some frequently asked questions about Honda CBX Pro motorcycle brakes. This way, you can find answers to some of the most common issues and prepare yourself for the next time you need to take your bike into the shop.
Honda CBX Pro Faults :
Another drawback that may occur along with your bike engine could be a blown gasket. this will cause your engine to overheat and presumably crack the cylinder heads. during this case, it's best to require your Honda CBX Pro bike to an expert mechanic to possess it verified. Another common drawback is with the carburettor. The carburettor is that the a part of your bike that mixes air and fuel to make the combustion required to power the engine.
HONDA Motorcycle Fault Codes DTC list
| Code (MIL) | Cause (a, b, c, ...) | Symptoms |
|---|---|---|
| Steady on | There is a jumper in the service connector; not faulty controlnunit (ECM); short circuit in the service connector | Engine is operating normally |
| No light |
a) ECM power failure b) Tilt sensor defective c) Open in the tilt sensor circuit d) Malfunctioning engine stop relay e) Open in the engine stop relay circuit f) Engine breaker not working properly g) Open in engine stop switch circuit h) The ignition switch is not working i) Not good ECM j) Blown fuse PGM-FI (20A) k) Open circuit in engine stop circuit l) Starter / ignition fuse blown (10A) | Engine fails to start |
| No light | An open in the MIL circuit of the indicator | Not OK ECM Engine running fine |
| 1 |
a) MAP sensor contact is off or not b) Open in MAP sensor circuit c) Malfunctioning MAP sensor | Engine is operating normally |
| 2 | Vacuum hose MAP sensor is removed or disconnected Malfunctioning MAP sensor | Engine is operating normally |
| 7 |
a) Whether the contact of the FCT sensor moves away b) Open or short in ECT sensor circuit c) Faulty ECT sensor | Heavy engine start at low temperature |
| 8 |
a) TP contact of the sensor moves away or not b) Open or short in TP sensor circuit c) Faulty TP sensor | Poor engine feedback on throttle opening |
| 9 |
a) Whether the contact of the IAT sensor moves away or not b) Open or short in IAT sensor circuit c) c) AT sensor defective | Engine running normally |
| 11 |
a) The contact of the speedometer sensor b) An open or short in the speedometer sensor circuit c) Speedometer sensor defective | Engine running normally |
| 12 |
a) The contact of the injector No. 1 connector is removed or not b) Open or short in injector No. 1 connector circuit c) Injector No 1 defective | Engine does not start |
| 13 |
a) The contact of the injector No. 2 connector is removed or not b) Open or short in injector No. 2 connector circuit c) c) Injector No. 2 is not working | The engine does not start |
| 14 |
a) The contact of the injector No. 3 connector is removed or not b) Open or short in injector No. 3 connector circuit c) Injector No. 3 is not working | The engine does not start |
| 15 |
a) The contact of the injector No. 4 connector is removed or not b) Open or short in the injector No. 4 connector circuit c) Injector No. 4 is not working | The engine does not start |
| 18 |
a) Whether or not the contact of the pulse generator sensor
connector moves away b) Open or short in the pulse generator sensor connector circuit c) Pulse generator sensor defective | Engine does not start |
| 19 |
a) Whether or not the contact of the pulse ignition sensor departs b) Open or short in the pulse ignition sensor circuit c) c) Pulse ignition sensor defective | Engine does not start |
| 21 | O2 sensor defective (California only) | Engine is operating normally |
| 23 | Faulty O2 heating sensor (California only) | Engine is operating normally |
| 33 | Damaged E2-PROM in ECM Engine running normally | Self-diagnosis not saved |
Honda MIL Failure Codes
The PGM-FI MIL denotes the failure codes (the number of blinks from 0 to 54). When the indicator lights for 1.3 seconds, it is equivalent to ten blinks. For example; a 1.3 second illumination and two blinks (0.5 second x 2) of the indicator equals 12 blinks. Follow code 12 troubleshooting.
When more than one failure occurs, the MIL shows the blinks in the order of lowest number to highest number. For example; if the indicator blinks once, then seven times, two failures have occurred. Follow codes 1 and 7 troubleshooting.
| Number of blinks | Causes | Symptoms | |
|---|---|---|---|
| 0 | No blinks | Faulty ECM | Engine does not start |
| 0 | No blinks | Faulty ECM (PGM-FI warning indicator output) | Engine operates normally |
| 0 | Stay lit | Short circuit in service check connector Faulty ECM (PGM-FI warning indicator output) | Engine operates normally |
| 1 | Blink | Open or short circuit in MAP sensor line (in the ECM) Faulty MAP sensor | Poor idle |
| 7 | Blinks | Loose or poor contact on ECT sensor Open or short circuit in ECT sensor wire Faulty ECT sensor | Hard starting at a low temperature (Simulate using numerical values; 90 C/194 F) Cooling fan does not stop |
| 8 | Blinks | Open or short circuit in TP sensor line (in the ECM) Faulty TP sensor | Poor engine response when operating the throttle quickly (Simulate using numerical values; throttle open 0) |
| 9 | Blinks | Open or short circuit in IAT sensor line (in the ECM) | Engine operates normally (Simulate using numerical values; 25 C/77 F) |
| 12 | Blinks | Loose or poor contact on injector connector Open or short circuit in injector wire Faulty injector | Engine does not start |
| 21 | Blinks | Loose or poor contact on O2 sensor Open or short circuit in O2 sensor wire Faulty O2 sensor | Engine operates normally |
| 54 | Blinks | Loose or poor contact on bank angle sensor connector Open circuit in bank angle sensor wire Faulty bank angle sensor | Engine starts but stops after few seconds. |
Honda CBX Pro Motorcycle Problems :
- Honda cbx pro after fire
- Honda cbx pro air cleaner clogged, poorly sealed, or missing
- Honda cbx pro air cleaner element clogged
- Honda cbx pro air duct loose
- Honda cbx pro air suction valve trouble
- Honda cbx pro air switching valve trouble
- Honda cbx pro backfiring when deceleration
- Honda cbx pro cracked or obstructed intake air pressure sensor
- Honda cbx pro crankshaft sensor trouble
- Honda cbx pro eCU ground and power supply trouble
- Honda cbx pro eCU trouble
- Honda cbx pro engine overheating - Water temperature sensor or crankshaft sensor trouble
- Honda cbx pro engine stalls easily
- Honda cbx pro engine vacuum not synchronizing
- Honda cbx pro exhaust Smokes Excessively
- Honda cbx pro firing incorrect
- Honda cbx pro fuel filter clogged
- Honda cbx pro fuel injector clogged
- Honda cbx pro fuel injector O-ring damage
- Honda cbx pro fuel injector trouble
- Honda cbx pro fuel line clogged
- Honda cbx pro fuel poor quality or incorrect
- Honda cbx pro fuel pressure regulator trouble
- Honda cbx pro fuel pressure too low or too high
- Honda cbx pro fuel pump bearings may wear. Replace the fuel pump
- Honda cbx pro fuel pump not operating
- Honda cbx pro fuel pump operates intermittently and often DFI fuse blows
- Honda cbx pro fuel pump relay trouble
- Honda cbx pro fuel pump trouble
- Honda cbx pro fuel/air mixture incorrect
- Honda cbx pro fuel/air mixture incorrect
- Honda cbx pro gear position sensor, starter lockout or side stand switch trouble
- Honda cbx pro inspect and repair or replace
- Honda cbx pro intake air pressure sensor trouble
- Honda cbx pro intake air temperature sensor trouble
- Honda cbx pro intake air temperature sensor trouble
- Honda cbx pro intermittent any DFI fault and its recovery
- Honda cbx pro little fuel in tank
- Honda cbx pro main throttle sensor trouble
- Honda cbx pro no or little fuel in tank
- Honda cbx pro poor acceleration
- Honda cbx pro spark plug burned or gap maladjusted
- Honda cbx pro spark plug dirty, broken or gap maladjusted
- Honda cbx pro spark plug incorrect
- Honda cbx pro spark weak
- Honda cbx pro stick coil shorted or not in good contact
- Honda cbx pro stick coil trouble
- Honda cbx pro subthrottle sensor trouble
- Honda cbx pro subthrottle valve actuator trouble
- Honda cbx pro throttle body assy dust seal damage
- Honda cbx pro throttle body assy holder loose
- Honda cbx pro throttle valves will not fully open
- Honda cbx pro unstable (rough) idling
- Honda cbx pro unstable fuel pressure
- Honda cbx pro vacuum hose
- Honda cbx pro vehicle-down sensor trouble
- Honda cbx pro water or foreign matter in fuel Change fuel
- Honda cbx pro water temperature sensor trouble
The first sign that your Honda CBX Pro motorcycle's starter system is working well is the warning light that appears when you switch on the ignition. It will illuminate for a few seconds, and then go out. This is a good sign that your starter system is working properly and you'll be able to start your motorcycle without difficulty.
Possible Failure Types :
- Strange Honda CBX Pro engine noise.
- Honda CBX Pro fog from engine.
- Strange Honda CBX Pro engine noise.
- Honda CBX Pro Vibrations and Rattling
- Honda CBX Pro Loud Acceleration
- Honda CBX Pro rusty exhaust
- Honda CBX Pro blockages in exhaust pipe
- Honda CBX Pro wear and tear exhaust
Honda Motor Company is by far the world's biggest motorcycle maker. Honda's first motorcycle was born out of necessity in immediate post World War II Japan, where public transportation was desperately overcrowded and gasoline severely restricted.Honda's first bikes were very successful and supplies of the surplus engines ran out after a few months. Business was good by then, so he decided to manufacture his own motors. Using the surplus motor as a model, Honda designed and built his own 50cc engine.
Check other Honda fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Honda check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Honda and logo are registered trademarks of Honda. We are fan of MOTORCYCLES ! We love them.