Honda CX 650 Fault Codes
Honda CX 650 motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following honda cx 650 faults are the list of some of the parts of a motorcycle engine.
One of the most common issues with Honda CX 650 motorcycle electrical systems is a clogged battery terminal. This can cause your ride to start having issues with the electrical components. Discolored terminals are often caused by a build-up of corrosion. This will prevent electrons from flowing properly, which reduces your ride’s electrical performance.
Honda CX 650 Faults :
Engine management systems of Honda CX 650 are responsible for monitoring a range of features and its warning light should go out a few seconds after ignition. The system's main job is to keep the engine running at peak performance by monitoring many parameters like coolant temperature, oil pressure, fuel level and air/fuel ratio. The system monitors these parameters continuously and alerts the driver if any of these parameters fall outside the predetermined limits.
HONDA Motorcycle Fault Codes DTC list
| Code (MIL) | Cause (a, b, c, ...) | Symptoms |
|---|---|---|
| Steady on | There is a jumper in the service connector; not faulty controlnunit (ECM); short circuit in the service connector | Engine is operating normally |
| No light |
a) ECM power failure b) Tilt sensor defective c) Open in the tilt sensor circuit d) Malfunctioning engine stop relay e) Open in the engine stop relay circuit f) Engine breaker not working properly g) Open in engine stop switch circuit h) The ignition switch is not working i) Not good ECM j) Blown fuse PGM-FI (20A) k) Open circuit in engine stop circuit l) Starter / ignition fuse blown (10A) | Engine fails to start |
| No light | An open in the MIL circuit of the indicator | Not OK ECM Engine running fine |
| 1 |
a) MAP sensor contact is off or not b) Open in MAP sensor circuit c) Malfunctioning MAP sensor | Engine is operating normally |
| 2 | Vacuum hose MAP sensor is removed or disconnected Malfunctioning MAP sensor | Engine is operating normally |
| 7 |
a) Whether the contact of the FCT sensor moves away b) Open or short in ECT sensor circuit c) Faulty ECT sensor | Heavy engine start at low temperature |
| 8 |
a) TP contact of the sensor moves away or not b) Open or short in TP sensor circuit c) Faulty TP sensor | Poor engine feedback on throttle opening |
| 9 |
a) Whether the contact of the IAT sensor moves away or not b) Open or short in IAT sensor circuit c) c) AT sensor defective | Engine running normally |
| 11 |
a) The contact of the speedometer sensor b) An open or short in the speedometer sensor circuit c) Speedometer sensor defective | Engine running normally |
| 12 |
a) The contact of the injector No. 1 connector is removed or not b) Open or short in injector No. 1 connector circuit c) Injector No 1 defective | Engine does not start |
| 13 |
a) The contact of the injector No. 2 connector is removed or not b) Open or short in injector No. 2 connector circuit c) c) Injector No. 2 is not working | The engine does not start |
| 14 |
a) The contact of the injector No. 3 connector is removed or not b) Open or short in injector No. 3 connector circuit c) Injector No. 3 is not working | The engine does not start |
| 15 |
a) The contact of the injector No. 4 connector is removed or not b) Open or short in the injector No. 4 connector circuit c) Injector No. 4 is not working | The engine does not start |
| 18 |
a) Whether or not the contact of the pulse generator sensor
connector moves away b) Open or short in the pulse generator sensor connector circuit c) Pulse generator sensor defective | Engine does not start |
| 19 |
a) Whether or not the contact of the pulse ignition sensor departs b) Open or short in the pulse ignition sensor circuit c) c) Pulse ignition sensor defective | Engine does not start |
| 21 | O2 sensor defective (California only) | Engine is operating normally |
| 23 | Faulty O2 heating sensor (California only) | Engine is operating normally |
| 33 | Damaged E2-PROM in ECM Engine running normally | Self-diagnosis not saved |
Honda MIL Failure Codes
The PGM-FI MIL denotes the failure codes (the number of blinks from 0 to 54). When the indicator lights for 1.3 seconds, it is equivalent to ten blinks. For example; a 1.3 second illumination and two blinks (0.5 second x 2) of the indicator equals 12 blinks. Follow code 12 troubleshooting.
When more than one failure occurs, the MIL shows the blinks in the order of lowest number to highest number. For example; if the indicator blinks once, then seven times, two failures have occurred. Follow codes 1 and 7 troubleshooting.
| Number of blinks | Causes | Symptoms | |
|---|---|---|---|
| 0 | No blinks | Faulty ECM | Engine does not start |
| 0 | No blinks | Faulty ECM (PGM-FI warning indicator output) | Engine operates normally |
| 0 | Stay lit | Short circuit in service check connector Faulty ECM (PGM-FI warning indicator output) | Engine operates normally |
| 1 | Blink | Open or short circuit in MAP sensor line (in the ECM) Faulty MAP sensor | Poor idle |
| 7 | Blinks | Loose or poor contact on ECT sensor Open or short circuit in ECT sensor wire Faulty ECT sensor | Hard starting at a low temperature (Simulate using numerical values; 90 C/194 F) Cooling fan does not stop |
| 8 | Blinks | Open or short circuit in TP sensor line (in the ECM) Faulty TP sensor | Poor engine response when operating the throttle quickly (Simulate using numerical values; throttle open 0) |
| 9 | Blinks | Open or short circuit in IAT sensor line (in the ECM) | Engine operates normally (Simulate using numerical values; 25 C/77 F) |
| 12 | Blinks | Loose or poor contact on injector connector Open or short circuit in injector wire Faulty injector | Engine does not start |
| 21 | Blinks | Loose or poor contact on O2 sensor Open or short circuit in O2 sensor wire Faulty O2 sensor | Engine operates normally |
| 54 | Blinks | Loose or poor contact on bank angle sensor connector Open circuit in bank angle sensor wire Faulty bank angle sensor | Engine starts but stops after few seconds. |
Honda CX 650 Motorcycle Problems :
- Honda cx 650 after fire
- Honda cx 650 air cleaner clogged, poorly sealed, or missing
- Honda cx 650 air cleaner element clogged
- Honda cx 650 air duct loose
- Honda cx 650 air suction valve trouble
- Honda cx 650 air switching valve trouble
- Honda cx 650 backfiring when deceleration
- Honda cx 650 cracked or obstructed intake air pressure sensor
- Honda cx 650 crankshaft sensor trouble
- Honda cx 650 eCU ground and power supply trouble
- Honda cx 650 eCU trouble
- Honda cx 650 engine overheating - Water temperature sensor or crankshaft sensor trouble
- Honda cx 650 engine stalls easily
- Honda cx 650 engine vacuum not synchronizing
- Honda cx 650 exhaust Smokes Excessively
- Honda cx 650 firing incorrect
- Honda cx 650 fuel filter clogged
- Honda cx 650 fuel injector clogged
- Honda cx 650 fuel injector O-ring damage
- Honda cx 650 fuel injector trouble
- Honda cx 650 fuel line clogged
- Honda cx 650 fuel poor quality or incorrect
- Honda cx 650 fuel pressure regulator trouble
- Honda cx 650 fuel pressure too low or too high
- Honda cx 650 fuel pump bearings may wear. Replace the fuel pump
- Honda cx 650 fuel pump not operating
- Honda cx 650 fuel pump operates intermittently and often DFI fuse blows
- Honda cx 650 fuel pump relay trouble
- Honda cx 650 fuel pump trouble
- Honda cx 650 fuel/air mixture incorrect
- Honda cx 650 fuel/air mixture incorrect
- Honda cx 650 gear position sensor, starter lockout or side stand switch trouble
- Honda cx 650 inspect and repair or replace
- Honda cx 650 intake air pressure sensor trouble
- Honda cx 650 intake air temperature sensor trouble
- Honda cx 650 intake air temperature sensor trouble
- Honda cx 650 intermittent any DFI fault and its recovery
- Honda cx 650 little fuel in tank
- Honda cx 650 main throttle sensor trouble
- Honda cx 650 no or little fuel in tank
- Honda cx 650 poor acceleration
- Honda cx 650 spark plug burned or gap maladjusted
- Honda cx 650 spark plug dirty, broken or gap maladjusted
- Honda cx 650 spark plug incorrect
- Honda cx 650 spark weak
- Honda cx 650 stick coil shorted or not in good contact
- Honda cx 650 stick coil trouble
- Honda cx 650 subthrottle sensor trouble
- Honda cx 650 subthrottle valve actuator trouble
- Honda cx 650 throttle body assy dust seal damage
- Honda cx 650 throttle body assy holder loose
- Honda cx 650 throttle valves will not fully open
- Honda cx 650 unstable (rough) idling
- Honda cx 650 unstable fuel pressure
- Honda cx 650 vacuum hose
- Honda cx 650 vehicle-down sensor trouble
- Honda cx 650 water or foreign matter in fuel Change fuel
- Honda cx 650 water temperature sensor trouble
The first sign that your Honda CX 650 motorcycle's starter system is working well is the warning light that appears when you switch on the ignition. It will illuminate for a few seconds, and then go out. This is a good sign that your starter system is working properly and you'll be able to start your motorcycle without difficulty.
Possible Failure Types :
- Strange Honda CX 650 engine noise.
- Honda CX 650 fog from engine.
- Strange Honda CX 650 engine noise.
- Honda CX 650 Vibrations and Rattling
- Honda CX 650 Loud Acceleration
- Honda CX 650 rusty exhaust
- Honda CX 650 blockages in exhaust pipe
- Honda CX 650 wear and tear exhaust
Honda Motor Company is by far the world's biggest motorcycle maker. Honda's first motorcycle was born out of necessity in immediate post World War II Japan, where public transportation was desperately overcrowded and gasoline severely restricted.Honda's first bikes were very successful and supplies of the surplus engines ran out after a few months. Business was good by then, so he decided to manufacture his own motors. Using the surplus motor as a model, Honda designed and built his own 50cc engine.
Check other Honda fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Honda check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Honda and logo are registered trademarks of Honda. We are fan of MOTORCYCLES ! We love them.