Indian Sport Scout Fault Codes
Indian Sport Scout motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following indian sport scout faults are the list of some of the parts of a motorcycle engine.
Indian Sport Scout motorcycles are particularly vulnerable to exhaust fumes, so you’re right to be concerned about the fumes you breathed in. The good news is that you should be able to find a motorcycle maintenance checklist online or at your local dealership that will provide you with a list of potential issues that might be causing your bike to release harmful emissions.
Indian Sport Scout Faults :
Another drawback that may occur along with your bike engine could be a blown gasket. this will cause your engine to overheat and presumably crack the cylinder heads. during this case, it's best to require your Indian Sport Scout bike to an expert mechanic to possess it verified. Another common drawback is with the carburettor. The carburettor is that the a part of your bike that mixes air and fuel to make the combustion required to power the engine.
EFI diagnostic display mode is for informational purposes only. Please see your Indian Motorcycle dealer for diagnostic troubleshooting and repairs. The diagnostic mode is accessible only when the 'Check Engine' light (MIL) illuminates after the motorcycle has been powered on and a code has been set. Leave the ignition on if you want to view the active fault code. The diagnostic mode becomes inaccessible if the motorcycle is powered off and on and the 'Check Engine' light is no longer active. This allows the determination of persistent as well as intermittent faults. Inactive codes are stored in the history of the unit. Please see your Indian Motorcycle dealer to retrieve historical or inactive codes.
Diagnostic Code Display and Descriptions :
SPN | FMI | COMPONENT | CONDITION | MIL | CODE |
29 | 3 | Accelerator Position 2 | Voltage Too High | ON | P1228 |
4 | Voltage Too Low | ON | P1227 | ||
51 | 3 | Throttle Position Sensor 1 | Voltage Too High | ON | P0123 |
4 | Voltage Too Low | ON | P0122 | ||
84 | 0 | Vehicle Speed Signal | Vehicle Speed Too High | ON | C1057 |
2 | Data Erratic or Intermittent (or Missing) | ON | C1058 | ||
9 | Abnormal Update Rate | ON | P160A | ||
19 | Received Vehicle Speed has error | ON | C1069 | ||
ON | P106B | ||||
91 | 3 | Accelerator Position 1 | Voltage Too High | ON | P0228 |
4 | Voltage Too Low | ON | P0227 | ||
96 | 3 | Fuel Level Signal | Voltage Too High | OFF | P0463 |
4 | Voltage Too Low | OFF | P0462 | ||
100 | 3 | Engine Oil Pressure Sensor | Pressure Too High | ON | P0523 |
4 | Pressure Too Low | ON | P0522 | ||
102 | 3 | Manifold Absolute Pressure Sensor | Voltage Too High | ON | P0108 |
4 | Voltage Too Low | ON | P0107 | ||
105 | 3 | Intake Air Temperature Sensor | Voltage Too High | ON | P0113 |
4 | Voltage Too Low | ON | P0112 | ||
110 | 3 | Engine Temperature Sensor | Voltage Too High | ON | P0118 |
4 | Voltage Too Low | ON | P0117 | ||
16 | Temperature Too High | OFF | P0217 | ||
0 | Engine Overheat Shutdown | OFF | P1217 | ||
15 | Temperature Above Normal Range | OFF | P1116 | ||
168 | 3 | System Power (Battery Potential / Power Input) | Voltage Too High | OFF | P0563 |
ON | C1063 | ||||
4 | Voltage Too Low | OFF | P0562 | ||
ON | C1064 | ||||
1 | Voltage Below Critical Level | OFF | P1563 | ||
190 | 0 | Engine Speed | Engine Speed Too High | OFF | C1059 |
1 | Engine Speed Too Low | OFF | C1060 | ||
2 | Data Erratic or Intermittent (or Missing) | OFF | C1061 | ||
31 | Error in Engine Speed Computation | ON | P121C | ||
19 | Received Engine Speed has Error | OFF | C1066 | ||
523 | 3 | Gear Sensor Signal | Voltage Too High | ON | P0917 |
4 | Voltage Too Low | ON | P0916 | ||
11 | Signal Fault | ON | P0915 | ||
598 | 2 | Clutch Switch Signal | Signal Fault | OFF | P0704 |
628 | 12 | ECU Memory | EEPROM Read / Write Failure | ON | P1602 |
636 | 2 | Crankshaft Position Sensor | Plausibility Fault | ON | P0335 |
651 | 5 | Injector 1 (Front) | Driver Circuit Open/Grounded | ON | P0261 |
3 | Driver Circuit Short to B+ | ON | P0262 | ||
4 | Driver Circuit Grounded | ON | P1262 | ||
652 | 5 | Injector 2 (Rear) | Driver Circuit Open/Grounded | ON | P0264 |
3 | Driver Circuit Short to B+ | ON | P0265 | ||
4 | Driver Circuit Grounded | ON | P1265 | ||
677 | 5 | Starter Solenoid Driver Circuit | Driver Circuit Open/Grounded | OFF | P0615 |
3 | Driver Circuit Short to B+ | OFF | P0617 | ||
4 | Driver Circuit Grounded | OFF | P0616 | ||
731 | 4 | Knock Sensor 1 | Voltage Too Low | ON | P0327 |
SPN | FMI | COMPONENT | CONDITION | MIL | CODE |
904 | 5 | Wheel Speed Sensor (Front) | Open / Short | ON | C1030 |
2 | Input Abnormal / Signal Failure | ON | C1031 | ||
907 | 2 | Wheel Speed Sensor (Rear) | Plausibility Fault | ON | C103D |
3 | Short to B+ | ON | C113D | ||
4 | Open/Short to GND | ON | C123D | ||
5 | Open/Short | ON | C1036 | ||
8 | Abnormal Frequency | ON | C133D | ||
14 | Incorrect Sensor / Improper Mounting | ON | C143D | ||
1023 | 5 | Trip Sudden Decelerations | Open / Short | ON | C1045 |
1071 | 5 | Fan Relay Driver | Driver Circuit Open/Grounded | OFF | P1481 |
3 | Driver Circuit Short to B+ | OFF | P1482 | ||
4 | Driver Circuit Grounded | OFF | P1483 | ||
1268 | 3 | Ignition Coil Primary Driver 1 | Driver Circuit Short to B+ | ON | P1353 |
1269 | 3 | Ignition Coil Primary Driver 2 | Driver Circuit Short to B+ | ON | P1354 |
4 | Driver Circuit Grounded | ON | P1362 | ||
1347 | 5 | Fuel Pump Driver Circuit | Driver Circuit Open/Grounded | OFF | P0230 |
3 | Driver Circuit Short to B+ | OFF | P0232 | ||
4 | Driver Circuit Grounded | OFF | P0231 | ||
3056 | 3 | Oxygen Sensor 1 (Front) | Voltage High | ON | P0132 |
4 | Voltage Low | ON | P0131 | ||
3597 | 3 | ECU Output Supply Voltage 1 | Voltage Too High | OFF | P16A2 |
4 | Voltage Too Low | OFF | P16A1 | ||
3598 | 3 | ECU Output Supply Voltage 2 | Voltage Too High | OFF | P16A9 |
4 | Voltage Too Low | OFF | P16A8 | ||
3599 | 3 | ECU Output Supply Voltage 3 | Voltage Too High | OFF | P17AA |
4 | Voltage Too Low | OFF | P17AB | ||
65613 | 2 | ETC Accelerator Position Sensor Outputs 1 & 2 Correlation | Correlation Fault | ON | P1135 |
65590 | 7 | Cylinder Not Identified | Misfire Confirmed | ON | P0314 |
65591 | 7 | Cylinder 1 | Misfire Detected | ON | P0301 |
65592 | 7 | Cylinder 2 | Misfire Detected | ON | P0302 |
520198 | 3 | Throttle Position Sensor 2 | Voltage Too High | ON | P0223 |
4 | Voltage Too Low | ON | P0222 | ||
520200 | 2 | Tipover Sensor | Signal Fault | OFF | P1501 |
3 | Voltage High | OFF | P1503 | ||
4 | Voltage Low | OFF | P1502 | ||
14 | Condition Exists (tip over condition detected) | OFF | P1504 | ||
5 | Open Circuit | OFF | P1512 | ||
520202 | 5 | Canister Purge Valve | Driver Circuit Open/Grounded | ON | P0444 |
3 | Driver Circuit Short to B+ | ON | P0443 | ||
4 | Driver Circuit Grounded | ON | P0445 | ||
520208 | 5 | Chassis/Acc Relay | Driver Circuit Open/Grounded | OFF | P1611 |
3 | Driver Circuit Short to B+ | OFF | P1614 | ||
4 | Driver Circuit Grounded | OFF | P1613 | ||
520209 | 5 | Oxygen Sensor Heater 1 (pre) (front) | Driver Circuit Open/Grounded | ON | P0030 |
3 | Driver Circuit Short to B+ | ON | P0032 | ||
4 | Driver Circuit Grounded | ON | P0031 | ||
520210 | 5 | Oxygen Sensor Heater 2 (post) (rear) | Driver Circuit Open/Grounded | ON | P0036 |
3 | Driver Circuit Short to B+ | ON | P0038 | ||
4 | Driver Circuit Grounded | ON | P0037 | ||
520250 | 7 | ABS Pulsar (front) | COG Chip | ON | C1022 |
4
SPN | FMI | COMPONENT | CONDITION | MIL | CODE |
520251 | 7 | ABS Pulsar (rear) | COG Chip | ON | C1023 |
520252 | 5 | ABS Solenoid (RRI) | Open / Short | ON | C1024 |
520253 | 5 | ABS Solenoid (RRO) | Open / Short | ON | C1025 |
520254 | 5 | ABS Solenoid (FFI) | Open/Short | ON | C1026 |
520255 | 5 | ABS Solenoid (FFO) | Open/Short | ON | C1027 |
520256 | 5 | ABS Solenoid (RFI) | Open/Short | ON | C1028 |
520257 | 5 | ABS Solenoid (RFO) | Open/Short | ON | C1029 |
520258 | 11 | ABS Actuator (front) | Wheel Lock (or VSS failure) ABS On | ON | C1032 |
520259 | 11 | ABS Actuator (rear) | Wheel Lock (or VSS failure) ABS On | ON | C1033 |
520260 | 8 | ABS Motor | Motor Lock | ON | C0020 |
3 | Off Stick | ON | C1020 | ||
4 | On Stick | ON | C1021 | ||
520314 | 11 | ABS Actuator (rear) | Wheel Lock (or VSS failure) ABS Off | ON | C103B |
520261 | 7 | ABS Fail Safe Relay | On/Off Stick | ON | C1034 |
520262 | 4 | ABS Source Voltage | Drop | ON | C1038 |
3 | Raise | ON | C1039 | ||
520263 | 31 | ABS Tire | Irregular Tire Size | ON | C1040 |
520264 | 12 | ABS ECU | ECU Error | ON | C1041 |
520265 | 7 | ABS Module | Incomplete Evacuation and Fill | ON | C1042 |
520267 | 31 | Side-Stand Switch | Condition Exists (engine disabled due to extended side-stand) | OFF | P181C |
520276 | 12 | Throttle Position Sensor (1 or 2 Indeterminable) | Neither Position Sensor Passed Test | ON | P150B |
2 | Position Sensor Correlation Fault (One okay, one failed) | ON | P150C | ||
520277 | 3 | Throttle Body Control - Power Stage | Maximum | ON | P150D |
4 | Minimum | ON | P150E | ||
2 | Not Plausible | ON | P151A | ||
8 | Signal Error | ON | P151B | ||
520279 | 31 | Throttle Body Control - Adaption Aborted | Condition Exists | ON | P151D |
520280 | 31 | Throttle Body Control - Limp Home Position Check Failed | Condition Exists | ON | P151E |
520281 | 31 | Throttle Body Control - Mechanical Stop Adaptation Failure | Condition Exists | ON | P152A |
520282 | 31 | Throttle Body Control | Condition Exists | ON | P152B |
520283 | 3 | Throttle Body Control | Maximum | ON | P152C |
4 | Minimum | ON | P152D | ||
520284 | 31 | Throttle Body Control - Position Deviation Fault | Condition Exists | ON | P152E |
520286 | 31 | ECU Monitoring Error | Condition Exists | ON | P1540 |
520287 | 31 | ECU Monitoring Error (Level 3) | Condition Exists | ON | P1541 |
520288 | 31 | ECU Monitoring of Injection Cut Off(Level 1) | Condition Exists | ON | P1542 |
520289 | 31 | ECU Monitoring of Injection Cut Off(Level 2) | Condition Exists | ON | P1543 |
520305 | 31 | Throttle Body Control - requested throttle angle not plausible | Condition Exists | ON | P1530 |
520311 | 31 | ECU Fault – Hardware Disruption | Condition Exists | ON | P1537 |
520313 | 11 | ABS Actuator (front) | Wheel Lock (or VSS failure) ABS Off | ON | C103A |
520320 | 5 | Brake Light | Open Circuit | OFF | P1593 |
3 | Shorted to Battery | OFF | P1594 | ||
4 | Shorted to Ground | OFF | P1595 | ||
520323 | 3 | Rear Brake Switch | Voltage Too High | ON | P159C |
520329 | 9 | Operator Switch Status (pOSS1) | Abnormal Update Rate | ON | P1063 |
520331 | 3 | Knock Sensor Positive Line | Voltage Too High | ON | P1327 |
4 | Voltage Too Low | ON | P1328 |
SPN | FMI | COMPONENT | CONDITION | MIL | CODE |
520332 | 3 | Knock Sensor Negative Line | Voltage Too High | ON | P132A |
4 | Voltage Too Low | ON | P132B | ||
520333 | 3 | Oxygen Sensor (Pre) (BANK 2) | Voltage High | ON | P1137 |
4 | Voltage Low | ON | P1138 | ||
520344 | 15 | Adaptive Fuel Correction Bank 1 | Data Valid But Above Normal Operating Range - Least Severe Level (System Too Rich) | ON | P0170 |
17 | Data Valid But Below Normal Operating Range - Least Severe Level (System Too Lean) | ON | P1170 | ||
520345 | 15 | Adaptive Fuel Correction Bank 2 | Data Valid But Below Normal Operating Range - Least Severe Level (System Too Rich) | ON | P0173 |
17 | Data Valid But Below Normal Operating Range - Least Severe Level (System Too Lean) | ON | P1173 | ||
524046 | 9 | Start Button | Abnormal Update Rate | OFF | U1FFD |
524079 | 31 | Cruise Control Input Checksum | Checksum does not match | ON | U0405 |
524080 | 31 | Cruise Control Input Message Counter | Counter not incremented | ON | U1405 |
ABS Trouble Codes
4
SPN | FMI | COMPONENT | CONDITION | ABS LAMP ON (YES / NO) | TRACTION CONTROL LAMP ON (YES / NO) | CODE | SERVICE ACTION |
520140 | 12 | ABS ECU | Bad Intelligent Device | Yes | Yes | C2437 | Replace Module |
520131 | 12 | ABS Valve Relay | Condition Exists | Yes | Yes | C2420 | Replace Module |
520254 | 31 | ABS Solenoid (Front In) | Condition Exists | Yes | Yes | C1326 | Replace Module |
520255 | 31 | ABS Solenoid (Front Out) | Condition Exists | Yes | Yes | C1327 | Replace Module |
520252 | 31 | ABS Solenoid (Rear In) | Condition Exists | Yes | Yes | C1330 | Replace Module |
520253 | 31 | ABS Solenoid (Rear Out) | Condition Exists | Yes | Yes | C1332 | Replace Module |
520262 | 0 | ABS Controller Source Voltage | Data valid but above normal operational range | Yes | Yes | C2422 | Check Battery Voltage |
1 | Data valid but above below operational range | Yes | Yes | 2421 | |||
3 | Voltage above normal | No | Yes | 1039 | |||
4 | Voltage below normal | No | Yes | 1038 | |||
520132 | 31 | ABS Pressure Sensor | ABS internal pressure sensor supply voltage faulty | Yes | Yes | C2423 | Replace ABS Module |
520133 | 12 | ABS Internal Pressure Sensor | Bad Intelligent Device | Yes | Yes | C2424 | Replace ABS Module |
2 | Data Erratic, intermittent, or incorrect | Yes | Yes | C2439 | Cycle Key 3–4 times. Replace module if unsuccessful | ||
520260 | 12 | ABS Motor | Bad Intelligent Device | Yes | Yes | C101C | Replace ABS Module |
520134 | 31 | ABS Motor Supply Failure | Condition Exists | Yes | Yes | C2425 | Check Motor Supply Voltage. Check Fuses |
904 | 2 | Front Wheel Speed Sensor | Data Erratic, Intermittent, or Incorrect | Yes | Yes | C1031 | Check Tone Ring for any abnormalities , Check for Bad Airgap and wheel vibrations |
3 | Voltage Above Normal | Yes | Yes | C2426 | Check Signal Line Voltage | ||
4 | Voltage Below Normal | Yes | Yes | C2427 | Check Supply/ Signal Line Voltage | ||
907 | 2 | Rear Wheel Speed Sensor | Data Erratic, Intermittent, or Incorrect | Yes | Yes | C103D | Check Tone Ring for any abnormalities , Check for Bad Airgap and wheel vibrations |
3 | Voltage Above Normal | Yes | Yes | C113D | Check Signal Line Voltage |
SPN | FMI | COMPONENT | CONDITION | ABS LAMP ON (YES / NO) | TRACTION CONTROL LAMP ON (YES / NO) | CODE | SERVICE ACTION |
4 | Voltage Below Normal | Yes | Yes | C123D | Check Supply/ Signal Line Voltage | ||
520135 | 31 | Wheel Speed Sensor | Wheel Speed Sensor Signal Error | Yes | Yes | C2430 | Check Tone Wheel Alignment /Airgap. |
65559 | 31 | CAN1 Bus Hardware | CAN Controller Failure | Yes | Yes | C1130 | Replace the ABS Module if multiple key cycles do not recover module. |
520141 | 31 | CAN1 Bus Wiring | CAN Wiring Issue | Yes | Yes | C2438 | Check the CAN wiring going into the module |
520136 | 7 | IMU (Inertial Measurement Unit) | Mechanical System Failure or Out of Adjustment | No | No | C2431 | Verify IMU Installation and Connections for abnormalities. |
2 | Data Erratic or Incorrect or Intermittent | No | No | C2432 | Verify IMU Installation and Connections for abnormalities. | ||
9 | Abnormal Update Rate | No | No | U0132 | Verify IMU Installation and Connections for abnormalities. | ||
22 | Counter Fault | No | No | U0133 | Verify IMU Installation and Connections for abnormalities. | ||
23 | Checksum Fault | No | No | U0134 | Verify IMU Installation and Connections for abnormalities. | ||
520137 | 31 | ABS Manually Disabled | Condition Exists | Yes | No | C2433 | No Service Action Required |
520138 | 31 | TC Manually Disabled | Condition Exists | No | Yes | C2434 | No Service Action Required |
520265 | 7 | ABS Module | Un-Filled Component | Yes (Flashing) | Yes | C1042 | — |
524077 | 2 | pDrive Mode Commanded | Data Invalid or Intermittent or Incorrect | No | No | C2435 | Check Wiring and Connection to ECM and ABS |
9 | Abnormal Update Rate | No | No | U0135 | |||
520139 | 9 | pTSCF1 | Abnormal Update Rate | No | Yes | U0136 | Check wiring and connection to ECM and ABS |
22 | Counter Fault | No | Yes | U0137 | |||
23 | Checksum Fault | No | Yes | U0138 | |||
513118 | 9 | 65314 Timing | Abnormal Update Rate | No | Yes | U1109 | Check wiring and connection to ECM and ABS |
516121 | 9 | 61445 Timing Gear Position | Abnormal Update Rate | No | Yes | U1111 | Check wiring and connection to ECM and ABS |
SPN | FMI | COMPONENT | CONDITION | ABS LAMP ON (YES / NO) | TRACTION CONTROL LAMP ON (YES / NO) | CODE | SERVICE ACTION |
516136 | 31 | PGN 61441 Missing EBC1–Lamp Info | Condition Exists | No | No | U1112 | Check wiring and connection to Gauge and ABS |
516120 | 9 | PGN 65265 Missing CCVS - Clutch Status | Abnormal Update Rate | No | Yes | U1106 | Check wiring and connections for Hand Controls and ABS |
520319 | 31 | Variant Invalid | Condition Exists | Yes | Yes | C1082 | Follow Variant Write Procedure within DW. |
14 | Data not Read Properly | Yes | Yes | C2436 | Verify the ABS Variant Procedure was successful |
Indian Sport Scout Motorcycle Problems :
- Indian sport scout after fire
- Indian sport scout air cleaner clogged, poorly sealed, or missing
- Indian sport scout air cleaner element clogged
- Indian sport scout air duct loose
- Indian sport scout air suction valve trouble
- Indian sport scout air switching valve trouble
- Indian sport scout backfiring when deceleration
- Indian sport scout cracked or obstructed intake air pressure sensor
- Indian sport scout crankshaft sensor trouble
- Indian sport scout eCU ground and power supply trouble
- Indian sport scout eCU trouble
- Indian sport scout engine overheating - Water temperature sensor or crankshaft sensor trouble
- Indian sport scout engine stalls easily
- Indian sport scout engine vacuum not synchronizing
- Indian sport scout exhaust Smokes Excessively
- Indian sport scout firing incorrect
- Indian sport scout fuel filter clogged
- Indian sport scout fuel injector clogged
- Indian sport scout fuel injector O-ring damage
- Indian sport scout fuel injector trouble
- Indian sport scout fuel line clogged
- Indian sport scout fuel poor quality or incorrect
- Indian sport scout fuel pressure regulator trouble
- Indian sport scout fuel pressure too low or too high
- Indian sport scout fuel pump bearings may wear. Replace the fuel pump
- Indian sport scout fuel pump not operating
- Indian sport scout fuel pump operates intermittently and often DFI fuse blows
- Indian sport scout fuel pump relay trouble
- Indian sport scout fuel pump trouble
- Indian sport scout fuel/air mixture incorrect
- Indian sport scout fuel/air mixture incorrect
- Indian sport scout gear position sensor, starter lockout or side stand switch trouble
- Indian sport scout inspect and repair or replace
- Indian sport scout intake air pressure sensor trouble
- Indian sport scout intake air temperature sensor trouble
- Indian sport scout intake air temperature sensor trouble
- Indian sport scout intermittent any DFI fault and its recovery
- Indian sport scout little fuel in tank
- Indian sport scout main throttle sensor trouble
- Indian sport scout no or little fuel in tank
- Indian sport scout poor acceleration
- Indian sport scout spark plug burned or gap maladjusted
- Indian sport scout spark plug dirty, broken or gap maladjusted
- Indian sport scout spark plug incorrect
- Indian sport scout spark weak
- Indian sport scout stick coil shorted or not in good contact
- Indian sport scout stick coil trouble
- Indian sport scout subthrottle sensor trouble
- Indian sport scout subthrottle valve actuator trouble
- Indian sport scout throttle body assy dust seal damage
- Indian sport scout throttle body assy holder loose
- Indian sport scout throttle valves will not fully open
- Indian sport scout unstable (rough) idling
- Indian sport scout unstable fuel pressure
- Indian sport scout vacuum hose
- Indian sport scout vehicle-down sensor trouble
- Indian sport scout water or foreign matter in fuel Change fuel
- Indian sport scout water temperature sensor trouble
Fault problems that can occur with yourIndian Sport Scoutmotorcycle engine is a blown head gasket. This can cause your engine to overheat and possibly crack the cylinder heads. In this case, it is best to take your Indian Sport Scout motorcycle to a professional mechanic to have it checked out. Another common problem is with the carburetor. The carburetor is the part of your motorcycle that mixes air and fuel to create the combustion needed to power the engine.
Possible Failure Types :
- Strange Indian Sport Scout engine noise.
- Indian Sport Scout fog from engine.
- Strange Indian Sport Scout engine noise.
- Indian Sport Scout Vibrations and Rattling
- Indian Sport Scout Loud Acceleration
- Indian Sport Scout rusty exhaust
- Indian Sport Scout blockages in exhaust pipe
- Indian Sport Scout wear and tear exhaust
Founded in 1901, Indian Motorcycles has had a tumultuous history, being the only other American motorcycle manufacturer to survive the Great Depression next to Harley. Today, Indian is famous for their modern take on classic styles, with a variety of touring and cruising models.
Check other Indian fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Indian check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Indian and logo are registered trademarks of Indian. We are fan of MOTORCYCLES ! We love them.