Kawasaki KX 100 Fault Codes
Kawasaki KX 100 motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following kawasaki kx 100 faults are the list of some of the parts of a motorcycle engine.
Checking the fault code is one of the most overlooked aspects of maintaining Kawasaki KX 100 motorcycle. Many people don’t think about it until something goes wrong. A clogged afuel pump. Now that you know how to stay visible on your bike, and how to stay safe on your Kawasaki KX 100 bike, it’s important that you know what you need. When you’re on a bike, the weather is often a factor. Here are a few tips that will help you protect yourself the next time you take your motorcycle out on the road.
Kawasaki KX 100 Faults :
The warning light comes on when one of the various sensors has detected an abnormal condition in the Kawasaki KX 100 engine's performance. For example, if the oil pressure drops below a certain threshold or if the air/fuel ratio rises beyond a certain point, then this would cause an immediate alert from your vehicle's engine management system.
Kawasaki Diagnosis
Under the seat, along the right subframe rail is a short orange/black wire with a bullet connector sticking out of the thick loom. This is the self-diagnosis terminal. There is another bullet connector protruding nearby - make sure it's the orange and black which can take some tugging. In order to read out the Service Codes below, ground that connector with a bit of wire with the motor running.
The red FI light will begin to flash codes. There will be a 5 second delay and then the codes begin. The first flash is always a LONG (1 sec) followed by either LONG or SHORT (0.5 sec) flashes. LONG flashes indicate TENS and short flashes ONES.
One LONG followed by two SHORT = 12. Two LONG, one SHORT = 21. Three LONG, two short = 32, etc. There is an interval of 1.5 seconds between TENS and ONES. There is a 3 second interval between codes.
To recover codes set in memory ground the self-diagnosis terminal rapidly more than 5 times within 2 seconds. The lead must remain grounded after 5 groundings for the remainder of the diagnostic session. You can then clear codes from the ECU by pulling the clutch lever in for more than 5 seconds.
KAWASAKI Motorcycles Fault Codes DTC List
Trouble Code | Problem Description |
---|---|
11 | Main throttle sensor malfunction, wiring open or short |
12 | Inlet air pressure sensor malfunction, wiring open or short |
13 | Inlet air temperature sensor malfunction, wiring open or short |
14 | Water temperature sensor malfunction, wiring open or short |
15 | Atmospheric pressure sensor malfunction, wiring open or short |
21 | Crankshaft sensor malfunction, wiring open or short |
23 | Camshaft position sensor malfunction, wiring open or short |
24 | Speed sensor malfunction, wiring open or short |
25 | Gear position switch malfunction, wiring open or short |
31 | Vehicle-down sensor malfunction, wiring open or short |
32 | Subthrottle sensor malfunction, wiring open or short |
33 | Oxygen sensor #1 inactivation, wiring open or short (Equipped Models) |
34 | Exhaust butterfly valve actuator sensor malfunction, wiring open or short |
35 | Immobilizer amplifier malfunction |
36 | Blank Key detection |
39 | ECU communication error |
51 | Stick coil #1 malfunction, wiring open or short |
52 | Stick coil #2 malfunction, wiring open or short |
53 | Stick coil #3 malfunction, wiring open or short |
54 | Stick coil #4 malfunction, wiring open or short |
56 | Radiator fan relay malfunction, wiring open or short |
62 | Subthrottle valve actuator malfunction, wiring open or short |
63 | Exhaust butterfly valve actuator malfunction, wiring open or short |
64 | Air switching valve malfunction, wiring open or short |
67 | Oxygen sensor heater malfunction, wiring open or short (Equipped Models) |
83 | Oxygen Sensor #2 inactivation, wiring open or shout (Equipped Models) |
94 | Oxygen sensor #1 malfunction, wiring open or short (Equipped Models) |
95 | Oxygen sensor #2 malfunction, wiring open or short (Equipped Models) |
Kawasaki KX 100 Motorcycle Problems :
- Kawasaki kx 100 after fire
- Kawasaki kx 100 air cleaner clogged, poorly sealed, or missing
- Kawasaki kx 100 air cleaner element clogged
- Kawasaki kx 100 air duct loose
- Kawasaki kx 100 air suction valve trouble
- Kawasaki kx 100 air switching valve trouble
- Kawasaki kx 100 backfiring when deceleration
- Kawasaki kx 100 cracked or obstructed intake air pressure sensor
- Kawasaki kx 100 crankshaft sensor trouble
- Kawasaki kx 100 eCU ground and power supply trouble
- Kawasaki kx 100 eCU trouble
- Kawasaki kx 100 engine overheating - Water temperature sensor or crankshaft sensor trouble
- Kawasaki kx 100 engine stalls easily
- Kawasaki kx 100 engine vacuum not synchronizing
- Kawasaki kx 100 exhaust Smokes Excessively
- Kawasaki kx 100 firing incorrect
- Kawasaki kx 100 fuel filter clogged
- Kawasaki kx 100 fuel injector clogged
- Kawasaki kx 100 fuel injector O-ring damage
- Kawasaki kx 100 fuel injector trouble
- Kawasaki kx 100 fuel line clogged
- Kawasaki kx 100 fuel poor quality or incorrect
- Kawasaki kx 100 fuel pressure regulator trouble
- Kawasaki kx 100 fuel pressure too low or too high
- Kawasaki kx 100 fuel pump bearings may wear. Replace the fuel pump
- Kawasaki kx 100 fuel pump not operating
- Kawasaki kx 100 fuel pump operates intermittently and often DFI fuse blows
- Kawasaki kx 100 fuel pump relay trouble
- Kawasaki kx 100 fuel pump trouble
- Kawasaki kx 100 fuel/air mixture incorrect
- Kawasaki kx 100 fuel/air mixture incorrect
- Kawasaki kx 100 gear position sensor, starter lockout or side stand switch trouble
- Kawasaki kx 100 inspect and repair or replace
- Kawasaki kx 100 intake air pressure sensor trouble
- Kawasaki kx 100 intake air temperature sensor trouble
- Kawasaki kx 100 intake air temperature sensor trouble
- Kawasaki kx 100 intermittent any DFI fault and its recovery
- Kawasaki kx 100 little fuel in tank
- Kawasaki kx 100 main throttle sensor trouble
- Kawasaki kx 100 no or little fuel in tank
- Kawasaki kx 100 poor acceleration
- Kawasaki kx 100 spark plug burned or gap maladjusted
- Kawasaki kx 100 spark plug dirty, broken or gap maladjusted
- Kawasaki kx 100 spark plug incorrect
- Kawasaki kx 100 spark weak
- Kawasaki kx 100 stick coil shorted or not in good contact
- Kawasaki kx 100 stick coil trouble
- Kawasaki kx 100 subthrottle sensor trouble
- Kawasaki kx 100 subthrottle valve actuator trouble
- Kawasaki kx 100 throttle body assy dust seal damage
- Kawasaki kx 100 throttle body assy holder loose
- Kawasaki kx 100 throttle valves will not fully open
- Kawasaki kx 100 unstable (rough) idling
- Kawasaki kx 100 unstable fuel pressure
- Kawasaki kx 100 vacuum hose
- Kawasaki kx 100 vehicle-down sensor trouble
- Kawasaki kx 100 water or foreign matter in fuel Change fuel
- Kawasaki kx 100 water temperature sensor trouble
Your motorcycle engine consists of a lot of parts such as the engine block, cylinder heads and pistons. It is important to make sure these are all clean and lubricated to avoid engine problems. Also remember that Kawasaki KX 100 motorcycle engine is a very delicate piece of machinery so it's best to handle it with care.
Possible Failure Types :
- Strange Kawasaki KX 100 engine noise.
- Kawasaki KX 100 fog from engine.
- Strange Kawasaki KX 100 engine noise.
- Kawasaki KX 100 Vibrations and Rattling
- Kawasaki KX 100 Loud Acceleration
- Kawasaki KX 100 rusty exhaust
- Kawasaki KX 100 blockages in exhaust pipe
- Kawasaki KX 100 wear and tear exhaust

Kawasaki Heavy Industries was started in 1878, as a producer of maritime equipment and vessels. Kawasaki began motorcycle manufacturing in the late 1960’s and today, their bikes are famous for being nearly bulletproof, and many of their models being friendly for new riders.
Check other Kawasaki fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Kawasaki check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Kawasaki and logo are registered trademarks of Kawasaki. We are fan of MOTORCYCLES ! We love them.