Kawasaki Ninja 300 Fault Codes

Kawasaki Ninja 300 motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following kawasaki ninja 300 faults are the list of some of the parts of a motorcycle engine.

The fault codes are essential to the Kawasaki Ninja 300 motorcycle operation, as they create the spark that ignites the mixture of air and fuel in the engine. Check to see that the spark plugs are not soiled with carbon. As a result, the spark plugs will provide a much weaker spark. The most common cause of soiled spark plugs is the improper installation of an air filter. The air filter prevents dirt from getting into the engine, but a faulty air filter will allow dirt to enter the carburetor.

Kawasaki Ninja 300 Faults :

Your bike engine consists of a great deal of elements like the casting, cylinder heads and pistons. it's necessary to form certain these area unit all clean and lubricated to avoid engine issues. Conjointly keep in mind that Kawasaki Ninja 300 motorbike engine could be a terribly delicate piece of machinery therefore it is best to handle it with care.

Kawasaki Diagnosis

Under the seat, along the right subframe rail is a short orange/black wire with a bullet connector sticking out of the thick loom. This is the self-diagnosis terminal. There is another bullet connector protruding nearby - make sure it's the orange and black which can take some tugging. In order to read out the Service Codes below, ground that connector with a bit of wire with the motor running.

The red FI light will begin to flash codes. There will be a 5 second delay and then the codes begin. The first flash is always a LONG (1 sec) followed by either LONG or SHORT (0.5 sec) flashes. LONG flashes indicate TENS and short flashes ONES.

One LONG followed by two SHORT = 12.
Two LONG, one SHORT = 21.
Three LONG, two short = 32, etc.
There is an interval of 1.5 seconds between TENS and ONES.
There is a 3 second
interval between codes.

To recover codes set in memory ground the self-diagnosis terminal rapidly more than 5 times within 2 seconds. The lead must remain grounded after 5 groundings for the remainder of the diagnostic session. You can then clear codes from the ECU by pulling the clutch lever in for more than 5 seconds.

KAWASAKI Motorcycles Fault Codes DTC List

Trouble Code	Problem Description
11	Main throttle sensor malfunction, wiring open or short
12	Inlet air pressure sensor malfunction, wiring open or short
13	Inlet air temperature sensor malfunction, wiring open or short
14	Water temperature sensor malfunction, wiring open or short
15	Atmospheric pressure sensor malfunction, wiring open or short
21	Crankshaft sensor malfunction, wiring open or short
23	Camshaft position sensor malfunction, wiring open or short
24	Speed sensor malfunction, wiring open or short
25	Gear position switch malfunction, wiring open or short
31	Vehicle-down sensor malfunction, wiring open or short
32	Subthrottle sensor malfunction, wiring open or short
33	Oxygen sensor #1 inactivation, wiring open or short (Equipped Models)
34	Exhaust butterfly valve actuator sensor malfunction, wiring open or short
35	Immobilizer amplifier malfunction
36	Blank Key detection
39	ECU communication error
51	Stick coil #1 malfunction, wiring open or short
52	Stick coil #2 malfunction, wiring open or short
53	Stick coil #3 malfunction, wiring open or short
54	Stick coil #4 malfunction, wiring open or short
56	Radiator fan relay malfunction, wiring open or short
62	Subthrottle valve actuator malfunction, wiring open or short
63	Exhaust butterfly valve actuator malfunction, wiring open or short
64	Air switching valve malfunction, wiring open or short
67	Oxygen sensor heater malfunction, wiring open or short (Equipped Models)
83	Oxygen Sensor #2 inactivation, wiring open or shout (Equipped Models)
94	Oxygen sensor #1 malfunction, wiring open or short (Equipped Models)
95	Oxygen sensor #2 malfunction, wiring open or short (Equipped Models)

Kawasaki Ninja 300 Motorcycle Problems :

Kawasaki ninja 300 after fire
Kawasaki ninja 300 air cleaner clogged, poorly sealed, or missing
Kawasaki ninja 300 air cleaner element clogged
Kawasaki ninja 300 air duct loose
Kawasaki ninja 300 air suction valve trouble
Kawasaki ninja 300 air switching valve trouble
Kawasaki ninja 300 backfiring when deceleration
Kawasaki ninja 300 cracked or obstructed intake air pressure sensor
Kawasaki ninja 300 crankshaft sensor trouble
Kawasaki ninja 300 eCU ground and power supply trouble
Kawasaki ninja 300 eCU trouble
Kawasaki ninja 300 engine overheating - Water temperature sensor or crankshaft sensor trouble
Kawasaki ninja 300 engine stalls easily
Kawasaki ninja 300 engine vacuum not synchronizing
Kawasaki ninja 300 exhaust Smokes Excessively
Kawasaki ninja 300 firing incorrect
Kawasaki ninja 300 fuel filter clogged
Kawasaki ninja 300 fuel injector clogged
Kawasaki ninja 300 fuel injector O-ring damage
Kawasaki ninja 300 fuel injector trouble
Kawasaki ninja 300 fuel line clogged
Kawasaki ninja 300 fuel poor quality or incorrect
Kawasaki ninja 300 fuel pressure regulator trouble
Kawasaki ninja 300 fuel pressure too low or too high
Kawasaki ninja 300 fuel pump bearings may wear. Replace the fuel pump
Kawasaki ninja 300 fuel pump not operating
Kawasaki ninja 300 fuel pump operates intermittently and often DFI fuse blows
Kawasaki ninja 300 fuel pump relay trouble
Kawasaki ninja 300 fuel pump trouble
Kawasaki ninja 300 fuel/air mixture incorrect
Kawasaki ninja 300 fuel/air mixture incorrect
Kawasaki ninja 300 gear position sensor, starter lockout or side stand switch trouble
Kawasaki ninja 300 inspect and repair or replace
Kawasaki ninja 300 intake air pressure sensor trouble
Kawasaki ninja 300 intake air temperature sensor trouble
Kawasaki ninja 300 intake air temperature sensor trouble
Kawasaki ninja 300 intermittent any DFI fault and its recovery
Kawasaki ninja 300 little fuel in tank
Kawasaki ninja 300 main throttle sensor trouble
Kawasaki ninja 300 no or little fuel in tank
Kawasaki ninja 300 poor acceleration
Kawasaki ninja 300 spark plug burned or gap maladjusted
Kawasaki ninja 300 spark plug dirty, broken or gap maladjusted
Kawasaki ninja 300 spark plug incorrect
Kawasaki ninja 300 spark weak
Kawasaki ninja 300 stick coil shorted or not in good contact
Kawasaki ninja 300 stick coil trouble
Kawasaki ninja 300 subthrottle sensor trouble
Kawasaki ninja 300 subthrottle valve actuator trouble
Kawasaki ninja 300 throttle body assy dust seal damage
Kawasaki ninja 300 throttle body assy holder loose
Kawasaki ninja 300 throttle valves will not fully open
Kawasaki ninja 300 unstable (rough) idling
Kawasaki ninja 300 unstable fuel pressure
Kawasaki ninja 300 vacuum hose
Kawasaki ninja 300 vehicle-down sensor trouble
Kawasaki ninja 300 water or foreign matter in fuel Change fuel
Kawasaki ninja 300 water temperature sensor trouble

The first sign that your Kawasaki Ninja 300 motorcycle's starter system is working well is the warning light that appears when you switch on the ignition. It will illuminate for a few seconds, and then go out. This is a good sign that your starter system is working properly and you'll be able to start your motorcycle without difficulty.

Possible Failure Types :

Strange Kawasaki Ninja 300 engine noise.
Kawasaki Ninja 300 fog from engine.
Strange Kawasaki Ninja 300 engine noise.
Kawasaki Ninja 300 Vibrations and Rattling
Kawasaki Ninja 300 Loud Acceleration
Kawasaki Ninja 300 rusty exhaust
Kawasaki Ninja 300 blockages in exhaust pipe
Kawasaki Ninja 300 wear and tear exhaust

Kawasaki Heavy Industries was started in 1878, as a producer of maritime equipment and vessels. Kawasaki began motorcycle manufacturing in the late 1960’s and today, their bikes are famous for being nearly bulletproof, and many of their models being friendly for new riders.

Check other Kawasaki fault codes.

Common abbreviations and their meanings below:

ABS: Anti-Lock Braking System
ACR: Automatic Compression Release
AFR: Air Fuel Ratio
AIS: Active Intake Solenoid
ATS: Air Temperature Sensor
BAS: Bank Angle Sensor
BCM: Body Control Module
CAN: Controller Area Network
CCM: Cruise Control Module
CKP: Crank Position Sensor
DLC: Datalink Connector
DTC: Diagnostic Trouble Codes
ECM: Electronic Control Module
ECT: Engine Coolant Temperature
ECU: Electronic Control Unit
EFI: Electronic Fuel Injection
EFP: Electronic Fuel Pump
ET: Engine Temperature sensor
FI: Fuel Injectors
FPR: Fuel Pressure Regulator
H-DSSS: Harley-Davidson® Smart Security System
HCU: Hydraulic Control Unit, ABS
HFSM: Hands Free Security Module
HO2S: Heated Oxygen Sensor
IAC: Idle Air Control actuator
IAT: Intake Air Temperature sensor
ICM: Ignition Control Module
IMAP: MAP + IAT in one unit
ISS: Ion Sensing System
JSS: Jiffy Stand Sensor
LHCM: Left Hand Control Module
MAP: Manifold Absolute Pressure sensor
MHR: Right Hand Control Module
RCM: Reverse Control Module
TCA: Throttle Control Actuator
TGS: Twist Grip Sensor
TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment
TPS: Throttle Position Sensor
TSM / TSSM: (Turn Signal / Turn Signal Security Module)
VE: Volume Efficiency
VIN: Vehicle Identification Number
VSS: Vehicle Speed Sensor
WSS: Wheel Speed Sensor

These abbreviations, and the accompanying list of trouble codes, can be a great start when your Kawasaki check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.

Kawasaki and logo are registered trademarks of Kawasaki. We are fan of MOTORCYCLES ! We love them.