Kawasaki VN 800 Fault Codes
Kawasaki VN 800 motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following kawasaki vn 800 faults are the list of some of the parts of a motorcycle engine.
One of the most common issues with Kawasaki VN 800 motorcycle electrical systems is a clogged battery terminal. This can cause your ride to start having issues with the electrical components. Discolored terminals are often caused by a build-up of corrosion. This will prevent electrons from flowing properly, which reduces your ride’s electrical performance.
Kawasaki VN 800 Faults :
Another drawback that may occur along with your bike engine could be a blown gasket. this will cause your engine to overheat and presumably crack the cylinder heads. during this case, it's best to require your Kawasaki VN 800 bike to an expert mechanic to possess it verified. Another common drawback is with the carburettor. The carburettor is that the a part of your bike that mixes air and fuel to make the combustion required to power the engine.
Kawasaki Diagnosis
Under the seat, along the right subframe rail is a short orange/black wire with a bullet connector sticking out of the thick loom. This is the self-diagnosis terminal. There is another bullet connector protruding nearby - make sure it's the orange and black which can take some tugging. In order to read out the Service Codes below, ground that connector with a bit of wire with the motor running.
The red FI light will begin to flash codes. There will be a 5 second delay and then the codes begin. The first flash is always a LONG (1 sec) followed by either LONG or SHORT (0.5 sec) flashes. LONG flashes indicate TENS and short flashes ONES.
One LONG followed by two SHORT = 12. Two LONG, one SHORT = 21. Three LONG, two short = 32, etc. There is an interval of 1.5 seconds between TENS and ONES. There is a 3 second interval between codes.
To recover codes set in memory ground the self-diagnosis terminal rapidly more than 5 times within 2 seconds. The lead must remain grounded after 5 groundings for the remainder of the diagnostic session. You can then clear codes from the ECU by pulling the clutch lever in for more than 5 seconds.
KAWASAKI Motorcycles Fault Codes DTC List
| Trouble Code | Problem Description |
|---|---|
| 11 | Main throttle sensor malfunction, wiring open or short |
| 12 | Inlet air pressure sensor malfunction, wiring open or short |
| 13 | Inlet air temperature sensor malfunction, wiring open or short |
| 14 | Water temperature sensor malfunction, wiring open or short |
| 15 | Atmospheric pressure sensor malfunction, wiring open or short |
| 21 | Crankshaft sensor malfunction, wiring open or short |
| 23 | Camshaft position sensor malfunction, wiring open or short |
| 24 | Speed sensor malfunction, wiring open or short |
| 25 | Gear position switch malfunction, wiring open or short |
| 31 | Vehicle-down sensor malfunction, wiring open or short |
| 32 | Subthrottle sensor malfunction, wiring open or short |
| 33 | Oxygen sensor #1 inactivation, wiring open or short (Equipped Models) |
| 34 | Exhaust butterfly valve actuator sensor malfunction, wiring open or short |
| 35 | Immobilizer amplifier malfunction |
| 36 | Blank Key detection |
| 39 | ECU communication error |
| 51 | Stick coil #1 malfunction, wiring open or short |
| 52 | Stick coil #2 malfunction, wiring open or short |
| 53 | Stick coil #3 malfunction, wiring open or short |
| 54 | Stick coil #4 malfunction, wiring open or short |
| 56 | Radiator fan relay malfunction, wiring open or short |
| 62 | Subthrottle valve actuator malfunction, wiring open or short |
| 63 | Exhaust butterfly valve actuator malfunction, wiring open or short |
| 64 | Air switching valve malfunction, wiring open or short |
| 67 | Oxygen sensor heater malfunction, wiring open or short (Equipped Models) |
| 83 | Oxygen Sensor #2 inactivation, wiring open or shout (Equipped Models) |
| 94 | Oxygen sensor #1 malfunction, wiring open or short (Equipped Models) |
| 95 | Oxygen sensor #2 malfunction, wiring open or short (Equipped Models) |
Kawasaki VN 800 Motorcycle Problems :
- Kawasaki vn 800 after fire
- Kawasaki vn 800 air cleaner clogged, poorly sealed, or missing
- Kawasaki vn 800 air cleaner element clogged
- Kawasaki vn 800 air duct loose
- Kawasaki vn 800 air suction valve trouble
- Kawasaki vn 800 air switching valve trouble
- Kawasaki vn 800 backfiring when deceleration
- Kawasaki vn 800 cracked or obstructed intake air pressure sensor
- Kawasaki vn 800 crankshaft sensor trouble
- Kawasaki vn 800 eCU ground and power supply trouble
- Kawasaki vn 800 eCU trouble
- Kawasaki vn 800 engine overheating - Water temperature sensor or crankshaft sensor trouble
- Kawasaki vn 800 engine stalls easily
- Kawasaki vn 800 engine vacuum not synchronizing
- Kawasaki vn 800 exhaust Smokes Excessively
- Kawasaki vn 800 firing incorrect
- Kawasaki vn 800 fuel filter clogged
- Kawasaki vn 800 fuel injector clogged
- Kawasaki vn 800 fuel injector O-ring damage
- Kawasaki vn 800 fuel injector trouble
- Kawasaki vn 800 fuel line clogged
- Kawasaki vn 800 fuel poor quality or incorrect
- Kawasaki vn 800 fuel pressure regulator trouble
- Kawasaki vn 800 fuel pressure too low or too high
- Kawasaki vn 800 fuel pump bearings may wear. Replace the fuel pump
- Kawasaki vn 800 fuel pump not operating
- Kawasaki vn 800 fuel pump operates intermittently and often DFI fuse blows
- Kawasaki vn 800 fuel pump relay trouble
- Kawasaki vn 800 fuel pump trouble
- Kawasaki vn 800 fuel/air mixture incorrect
- Kawasaki vn 800 fuel/air mixture incorrect
- Kawasaki vn 800 gear position sensor, starter lockout or side stand switch trouble
- Kawasaki vn 800 inspect and repair or replace
- Kawasaki vn 800 intake air pressure sensor trouble
- Kawasaki vn 800 intake air temperature sensor trouble
- Kawasaki vn 800 intake air temperature sensor trouble
- Kawasaki vn 800 intermittent any DFI fault and its recovery
- Kawasaki vn 800 little fuel in tank
- Kawasaki vn 800 main throttle sensor trouble
- Kawasaki vn 800 no or little fuel in tank
- Kawasaki vn 800 poor acceleration
- Kawasaki vn 800 spark plug burned or gap maladjusted
- Kawasaki vn 800 spark plug dirty, broken or gap maladjusted
- Kawasaki vn 800 spark plug incorrect
- Kawasaki vn 800 spark weak
- Kawasaki vn 800 stick coil shorted or not in good contact
- Kawasaki vn 800 stick coil trouble
- Kawasaki vn 800 subthrottle sensor trouble
- Kawasaki vn 800 subthrottle valve actuator trouble
- Kawasaki vn 800 throttle body assy dust seal damage
- Kawasaki vn 800 throttle body assy holder loose
- Kawasaki vn 800 throttle valves will not fully open
- Kawasaki vn 800 unstable (rough) idling
- Kawasaki vn 800 unstable fuel pressure
- Kawasaki vn 800 vacuum hose
- Kawasaki vn 800 vehicle-down sensor trouble
- Kawasaki vn 800 water or foreign matter in fuel Change fuel
- Kawasaki vn 800 water temperature sensor trouble
Fault problems that can occur with yourKawasaki VN 800motorcycle engine is a blown head gasket. This can cause your engine to overheat and possibly crack the cylinder heads. In this case, it is best to take your Kawasaki VN 800 motorcycle to a professional mechanic to have it checked out. Another common problem is with the carburetor. The carburetor is the part of your motorcycle that mixes air and fuel to create the combustion needed to power the engine.
Possible Failure Types :
- Strange Kawasaki VN 800 engine noise.
- Kawasaki VN 800 fog from engine.
- Strange Kawasaki VN 800 engine noise.
- Kawasaki VN 800 Vibrations and Rattling
- Kawasaki VN 800 Loud Acceleration
- Kawasaki VN 800 rusty exhaust
- Kawasaki VN 800 blockages in exhaust pipe
- Kawasaki VN 800 wear and tear exhaust
Kawasaki Heavy Industries was started in 1878, as a producer of maritime equipment and vessels. Kawasaki began motorcycle manufacturing in the late 1960’s and today, their bikes are famous for being nearly bulletproof, and many of their models being friendly for new riders.
Check other Kawasaki fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Kawasaki check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Kawasaki and logo are registered trademarks of Kawasaki. We are fan of MOTORCYCLES ! We love them.