KTM 420 GS Fault Codes
KTM 420 GS motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following ktm 420 gs faults are the list of some of the parts of a motorcycle engine.
The oil level of KTM 420 GS should be the same level in the dipstick, even when the engine is cold. You can check the oil level by removing the dipstick, holding the dipstick in your hand, and then reinserting the dipstick. Then, you’ll be able to see where the oil level is.
KTM 420 GS Faults :
Another drawback that may occur along with your bike engine could be a blown gasket. this will cause your engine to overheat and presumably crack the cylinder heads. during this case, it's best to require your KTM 420 GS bike to an expert mechanic to possess it verified. Another common drawback is with the carburettor. The carburettor is that the a part of your bike that mixes air and fuel to make the combustion required to power the engine.
KTM Motorcycle Engine Fault Codes :
| Code | Description |
|---|---|
| Constant | Tilt Sensor - input signal too high |
| Constant | Tilt Sensor - input signal too low |
| 2 | Crankshaft speed sensor - synchronization faulty |
| 2 | Crankshaft speed sensor - signal implausible |
| 2 | Crankshaft speed sensor - signal irregular |
| 2 | Crankshaft speed sensor - no signal |
| 6 | Throttle valve position sensor circuit A - adaption failed |
| 6 | Throttle valve position sensor circuit A - input signal too low |
| 6 | Throttle valve position sensor circuit A - input signal too high |
| 9 | Crankcase pressure sensor - short circuit to ground |
| 9 | Crankcase pressure sensor - open / short to plus |
| 9 | Ambient air pressure sensor - short circuit to ground |
| 9 | Ambient air pressure sensor - open / short circuit to plus |
| 12 | Coolant temperature sensor - input signal too low |
| 12 | Coolant temperature sensor - input signal too high |
| 13 | Intake air temperature sensor - input signal too low |
| 13 | Intake air temperature sensor - input signal too high |
| 14 | Crankcae pressure sensor - difference too high between sensor and engine ECU |
| 21 | Battery voltage - input voltage too low |
| 21 | Battery voltage - input voltage too high |
| 33 | Injection valve 0, cylinder 1- input signal too low |
| 33 | Injection valve 0, cylinder 1- input signal too high |
| 34 | Injection valve 1, cylinder 1- input signal too low |
| 34 | Injection valve 1, cylinder 1- input signal too high |
| 37 | Ignition coil - circuit fault |
| 41 | Fuel pump - short circuit to ground / open circuit |
| 41 | Fuel pump - open circuit / short circuit to plus |
| 42 | Oil pump - input signal too low |
| 42 | Oil pump - signal too high |
KTM Flash Codes :
Blink code of FI warning lamp (MIL) 02 FI warning lamp (MIL) flashes 2x short Error level condition Crankshaft position sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 06 FI warning lamp (MIL) flashes 6x short Error level condition Throttle position sensor circuit A - input signal too low Throttle position sensor circuit A - input signal too high Blink code of FI warning lamp (MIL) 09 FI warning lamp (MIL) flashes 9x short Error level condition Manifold absolute pressure sensor - input signal too low Manifold absolute pressure sensor - input signal too high Blink code of FI warning lamp (MIL) 11 FI warning lamp (MIL) flashes 1x long, 1x short Error level condition Idle control - engine speed below target value Idle control - engine speed above target value Blink code of FI warning lamp (MIL) 12 FI warning lamp (MIL) flashes 1x long, 2x short Error level condition Engine coolant temperature sensor - input signal too low Engine coolant temperature sensor - input signal too high 22 FLASH CODE 173 Blink code of FI warning lamp (MIL) 13 FI warning lamp (MIL) flashes 1x long, 3x short Error level condition Intake air temperature sensor - input signal too low Intake air temperature sensor - input signal too high Blink code of FI warning lamp (MIL) 14 FI warning lamp (MIL) flashes 1x long, 4x short Error level condition Fuel tank sensor - circuit fault Fuel tank sensor - short circuit to ground Fuel tank sensor - short circuit to plus Blink code of FI warning lamp (MIL) 15 FI warning lamp (MIL) flashes 1x long, 5x short Error level condition Rollover sensor - plausibility Rollover sensor - circuit fault Rollover sensor - short circuit to ground Rollover sensor - short circuit to plus Blink code of FI warning lamp (MIL) 16 FI warning lamp (MIL) flashes 1x long, 6x short Error level condition Radiator fan motor - circuit fault Radiator fan motor - input signal too low Radiator fan motor - input signal too high 22 FLASH CODE 174 Blink code of FI warning lamp (MIL) 17 FI warning lamp (MIL) flashes 1x long, 7x short Error level condition Lambda sensor - circuit fault Lambda sensor - input signal too low Lambda sensor - input signal too high Lambda sensor - no function Blink code of FI warning lamp (MIL) 18 FI warning lamp (MIL) flashes 1x long, 8x short Error level condition Engine diagnosis warning lamp (MIL) - circuit fault Engine diagnosis warning lamp (MIL) - short circuit to ground Engine diagnosis warning lamp (MIL) - short circuit to plus Blink code of FI warning lamp (MIL) 19 FI warning lamp (MIL) flashes 1x long, 9x short Error level condition Fuel pump lamp - circuit fault Low fuel warning lamp - input signal too low Low fuel warning lamp - input signal too high Blink code of FI warning lamp (MIL) 21 FI warning lamp (MIL) flashes 2x long, 1x short Error level condition Engine control relay - switch-off delay 22 FLASH CODE 175 Blink code of FI warning lamp (MIL) 22 FI warning lamp (MIL) flashes 2x long, 2x short Error level condition Engine speed signal - circuit fault Engine speed signal - input signal too low Engine speed signal - input signal too high Blink code of FI warning lamp (MIL) 23 FI warning lamp (MIL) flashes 2x long, 3x short Error level condition Travel speed sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 24 FI warning lamp (MIL) flashes 2x long, 4x short Error level condition System voltage - too low System voltage - too high System voltage - implausible value Blink code of FI warning lamp (MIL) 25 FI warning lamp (MIL) flashes 2x long, 5x short Error level condition Side stand switch - plausibility Side stand switch - circuit fault Side stand switch - short circuit to ground Side stand switch - short circuit to plus 22 FLASH CODE 176 Blink code of FI warning lamp (MIL) 26 FI warning lamp (MIL) flashes 2x long, 6x short Error level condition Sensor A reference voltage - input signal too low Sensor A reference voltage - input signal too high Blink code of FI warning lamp (MIL) 27 FI warning lamp (MIL) flashes 2x long, 7x short Error level condition Sensor B reference voltage - input signal too low Sensor B reference voltage - input signal too high Blink code of FI warning lamp (MIL) 33 FI warning lamp (MIL) flashes 3x long, 3x short Error level condition Injector - circuit fault Injector - input signal too low Injector - input signal too high Blink code of FI warning lamp (MIL) 41 FI warning lamp (MIL) flashes 4x long, 1x short Error level condition Fuel pump relay - circuit fault Fuel pump relay - input signal too low Fuel pump relay - input signal too high 22 FLASH CODE 177 Blink code of FI warning lamp (MIL) 45 FI warning lamp (MIL) flashes 4x long, 5x short Error level condition Lambda sensor heater - circuit fault Lambda sensor heater - short circuit to ground or open circuit Lambda sensor heater - input signal too high Blink code of FI warning lamp (MIL) 49 FI warning lamp (MIL) flashes 4x long, 9x short Error level condition Idle control - input signal too low Idle control - input signal too high Idle control - circuit fault
KTM 420 GS Motorcycle Problems :
- KTM 420 gs after fire
- KTM 420 gs air cleaner clogged, poorly sealed, or missing
- KTM 420 gs air cleaner element clogged
- KTM 420 gs air duct loose
- KTM 420 gs air suction valve trouble
- KTM 420 gs air switching valve trouble
- KTM 420 gs backfiring when deceleration
- KTM 420 gs cracked or obstructed intake air pressure sensor
- KTM 420 gs crankshaft sensor trouble
- KTM 420 gs eCU ground and power supply trouble
- KTM 420 gs eCU trouble
- KTM 420 gs engine overheating - Water temperature sensor or crankshaft sensor trouble
- KTM 420 gs engine stalls easily
- KTM 420 gs engine vacuum not synchronizing
- KTM 420 gs exhaust Smokes Excessively
- KTM 420 gs firing incorrect
- KTM 420 gs fuel filter clogged
- KTM 420 gs fuel injector clogged
- KTM 420 gs fuel injector O-ring damage
- KTM 420 gs fuel injector trouble
- KTM 420 gs fuel line clogged
- KTM 420 gs fuel poor quality or incorrect
- KTM 420 gs fuel pressure regulator trouble
- KTM 420 gs fuel pressure too low or too high
- KTM 420 gs fuel pump bearings may wear. Replace the fuel pump
- KTM 420 gs fuel pump not operating
- KTM 420 gs fuel pump operates intermittently and often DFI fuse blows
- KTM 420 gs fuel pump relay trouble
- KTM 420 gs fuel pump trouble
- KTM 420 gs fuel/air mixture incorrect
- KTM 420 gs fuel/air mixture incorrect
- KTM 420 gs gear position sensor, starter lockout or side stand switch trouble
- KTM 420 gs inspect and repair or replace
- KTM 420 gs intake air pressure sensor trouble
- KTM 420 gs intake air temperature sensor trouble
- KTM 420 gs intake air temperature sensor trouble
- KTM 420 gs intermittent any DFI fault and its recovery
- KTM 420 gs little fuel in tank
- KTM 420 gs main throttle sensor trouble
- KTM 420 gs no or little fuel in tank
- KTM 420 gs poor acceleration
- KTM 420 gs spark plug burned or gap maladjusted
- KTM 420 gs spark plug dirty, broken or gap maladjusted
- KTM 420 gs spark plug incorrect
- KTM 420 gs spark weak
- KTM 420 gs stick coil shorted or not in good contact
- KTM 420 gs stick coil trouble
- KTM 420 gs subthrottle sensor trouble
- KTM 420 gs subthrottle valve actuator trouble
- KTM 420 gs throttle body assy dust seal damage
- KTM 420 gs throttle body assy holder loose
- KTM 420 gs throttle valves will not fully open
- KTM 420 gs unstable (rough) idling
- KTM 420 gs unstable fuel pressure
- KTM 420 gs vacuum hose
- KTM 420 gs vehicle-down sensor trouble
- KTM 420 gs water or foreign matter in fuel Change fuel
- KTM 420 gs water temperature sensor trouble
Issues with the engine are typically caused by issues with the engine parts. Whether it is a fuel issue or an ignition problem, the engine parts should be inspected to determine the cause. Another issue that can occur is when the KTM 420 GS motorcycle engine is not working is a failure of the electrical system. This can cause the motorcycle to stall and not work correctly. The electrical system is typically the most complex system on a motorcycle.
Possible Failure Types :
- Strange KTM 420 GS engine noise.
- KTM 420 GS fog from engine.
- Strange KTM 420 GS engine noise.
- KTM 420 GS Vibrations and Rattling
- KTM 420 GS Loud Acceleration
- KTM 420 GS rusty exhaust
- KTM 420 GS blockages in exhaust pipe
- KTM 420 GS wear and tear exhaust
Through a very complicated series of events, the informal company started in Mattighofen, Austria in 1934 became KTM AG in 1992. KTM is now one of the largest European producers of motorcycles, and are world-famous for their nearly indestructible off-road and adventure bikes.
Check other KTM fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your KTM check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
KTM and logo are registered trademarks of KTM. We are fan of MOTORCYCLES ! We love them.