KTM 690 Enduro Fault Codes

KTM 690 Enduro motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following ktm 690 enduro faults are the list of some of the parts of a motorcycle engine.

One of the most common issues with KTM 690 Enduro motorcycle electrical systems is a clogged battery terminal. This can cause your ride to start having issues with the electrical components. Discolored terminals are often caused by a build-up of corrosion. This will prevent electrons from flowing properly, which reduces your ride’s electrical performance.

KTM 690 Enduro Faults :

Your bike engine consists of a great deal of elements like the casting, cylinder heads and pistons. it's necessary to form certain these area unit all clean and lubricated to avoid engine issues. Conjointly keep in mind that KTM 690 Enduro motorbike engine could be a terribly delicate piece of machinery therefore it is best to handle it with care.

KTM Motorcycle Engine Fault Codes :

CodeDescription
ConstantTilt Sensor - input signal too high
ConstantTilt Sensor - input signal too low
2Crankshaft speed sensor - synchronization faulty
2Crankshaft speed sensor - signal implausible
2Crankshaft speed sensor - signal irregular
2Crankshaft speed sensor - no signal
6Throttle valve position sensor circuit A - adaption failed
6Throttle valve position sensor circuit A - input signal too low
6Throttle valve position sensor circuit A - input signal too high
9Crankcase pressure sensor - short circuit to ground
9Crankcase pressure sensor - open / short to plus
9Ambient air pressure sensor - short circuit to ground
9Ambient air pressure sensor - open / short circuit to plus
12Coolant temperature sensor - input signal too low
12Coolant temperature sensor - input signal too high
13Intake air temperature sensor - input signal too low
13Intake air temperature sensor - input signal too high
14Crankcae pressure sensor - difference too high between sensor and engine ECU
21Battery voltage - input voltage too low
21Battery voltage - input voltage too high
33Injection valve 0, cylinder 1- input signal too low
33Injection valve 0, cylinder 1- input signal too high
34Injection valve 1, cylinder 1- input signal too low
34Injection valve 1, cylinder 1- input signal too high
37Ignition coil - circuit fault
41Fuel pump - short circuit to ground / open circuit
41Fuel pump - open circuit / short circuit to plus
42Oil pump - input signal too low
42Oil pump - signal too high

KTM Flash Codes :

Blink code of FI warning
lamp (MIL)
02 FI warning lamp (MIL) flashes 2x short
Error level condition Crankshaft position sensor - measurement range or power problem
Blink code of FI warning
lamp (MIL)
06 FI warning lamp (MIL) flashes 6x short
Error level condition Throttle position sensor circuit A - input signal too low
Throttle position sensor circuit A - input signal too high
Blink code of FI warning
lamp (MIL)
09 FI warning lamp (MIL) flashes 9x short
Error level condition Manifold absolute pressure sensor - input signal too low
Manifold absolute pressure sensor - input signal too high
Blink code of FI warning
lamp (MIL)
11 FI warning lamp (MIL) flashes 1x long, 1x short
Error level condition Idle control - engine speed below target value
Idle control - engine speed above target value
Blink code of FI warning
lamp (MIL)
12 FI warning lamp (MIL) flashes 1x long, 2x short
Error level condition Engine coolant temperature sensor - input signal too low
Engine coolant temperature sensor - input signal too high
22 FLASH CODE 173
Blink code of FI warning
lamp (MIL)
13 FI warning lamp (MIL) flashes 1x long, 3x short
Error level condition Intake air temperature sensor - input signal too low
Intake air temperature sensor - input signal too high
Blink code of FI warning
lamp (MIL)
14 FI warning lamp (MIL) flashes 1x long, 4x short
Error level condition Fuel tank sensor - circuit fault
Fuel tank sensor - short circuit to ground
Fuel tank sensor - short circuit to plus
Blink code of FI warning
lamp (MIL)
15 FI warning lamp (MIL) flashes 1x long, 5x short
Error level condition Rollover sensor - plausibility
Rollover sensor - circuit fault
Rollover sensor - short circuit to ground
Rollover sensor - short circuit to plus
Blink code of FI warning
lamp (MIL)
16 FI warning lamp (MIL) flashes 1x long, 6x short
Error level condition Radiator fan motor - circuit fault
Radiator fan motor - input signal too low
Radiator fan motor - input signal too high
22 FLASH CODE 174
Blink code of FI warning
lamp (MIL)
17 FI warning lamp (MIL) flashes 1x long, 7x short
Error level condition Lambda sensor - circuit fault
Lambda sensor - input signal too low
Lambda sensor - input signal too high
Lambda sensor - no function
Blink code of FI warning
lamp (MIL)
18 FI warning lamp (MIL) flashes 1x long, 8x short
Error level condition Engine diagnosis warning lamp (MIL) - circuit fault
Engine diagnosis warning lamp (MIL) - short circuit to ground
Engine diagnosis warning lamp (MIL) - short circuit to plus
Blink code of FI warning
lamp (MIL)
19 FI warning lamp (MIL) flashes 1x long, 9x short
Error level condition Fuel pump lamp - circuit fault
Low fuel warning lamp - input signal too low
Low fuel warning lamp - input signal too high
Blink code of FI warning
lamp (MIL)
21 FI warning lamp (MIL) flashes 2x long, 1x short
Error level condition Engine control relay - switch-off delay
22 FLASH CODE 175
Blink code of FI warning
lamp (MIL)
22 FI warning lamp (MIL) flashes 2x long, 2x short
Error level condition Engine speed signal - circuit fault
Engine speed signal - input signal too low
Engine speed signal - input signal too high
Blink code of FI warning
lamp (MIL)
23 FI warning lamp (MIL) flashes 2x long, 3x short
Error level condition Travel speed sensor - measurement range or power problem
Blink code of FI warning
lamp (MIL)
24 FI warning lamp (MIL) flashes 2x long, 4x short
Error level condition System voltage - too low
System voltage - too high
System voltage - implausible value
Blink code of FI warning
lamp (MIL)
25 FI warning lamp (MIL) flashes 2x long, 5x short
Error level condition Side stand switch - plausibility
Side stand switch - circuit fault
Side stand switch - short circuit to ground
Side stand switch - short circuit to plus
22 FLASH CODE 176
Blink code of FI warning
lamp (MIL)
26 FI warning lamp (MIL) flashes 2x long, 6x short
Error level condition Sensor A reference voltage - input signal too low
Sensor A reference voltage - input signal too high
Blink code of FI warning
lamp (MIL)
27 FI warning lamp (MIL) flashes 2x long, 7x short
Error level condition Sensor B reference voltage - input signal too low
Sensor B reference voltage - input signal too high
Blink code of FI warning
lamp (MIL)
33 FI warning lamp (MIL) flashes 3x long, 3x short
Error level condition Injector - circuit fault
Injector - input signal too low
Injector - input signal too high
Blink code of FI warning
lamp (MIL)
41 FI warning lamp (MIL) flashes 4x long, 1x short
Error level condition Fuel pump relay - circuit fault
Fuel pump relay - input signal too low
Fuel pump relay - input signal too high
22 FLASH CODE 177
Blink code of FI warning
lamp (MIL)
45 FI warning lamp (MIL) flashes 4x long, 5x short
Error level condition Lambda sensor heater - circuit fault
Lambda sensor heater - short circuit to ground or open circuit
Lambda sensor heater - input signal too high
Blink code of FI warning
lamp (MIL)
49 FI warning lamp (MIL) flashes 4x long, 9x short
Error level condition Idle control - input signal too low
Idle control - input signal too high
Idle control - circuit fault

KTM 690 Enduro Motorcycle Problems :

  • KTM 690 enduro after fire
  • KTM 690 enduro air cleaner clogged, poorly sealed, or missing
  • KTM 690 enduro air cleaner element clogged
  • KTM 690 enduro air duct loose
  • KTM 690 enduro air suction valve trouble
  • KTM 690 enduro air switching valve trouble
  • KTM 690 enduro backfiring when deceleration
  • KTM 690 enduro cracked or obstructed intake air pressure sensor
  • KTM 690 enduro crankshaft sensor trouble
  • KTM 690 enduro eCU ground and power supply trouble
  • KTM 690 enduro eCU trouble
  • KTM 690 enduro engine overheating - Water temperature sensor or crankshaft sensor trouble
  • KTM 690 enduro engine stalls easily
  • KTM 690 enduro engine vacuum not synchronizing
  • KTM 690 enduro exhaust Smokes Excessively
  • KTM 690 enduro firing incorrect
  • KTM 690 enduro fuel filter clogged
  • KTM 690 enduro fuel injector clogged
  • KTM 690 enduro fuel injector O-ring damage
  • KTM 690 enduro fuel injector trouble
  • KTM 690 enduro fuel line clogged
  • KTM 690 enduro fuel poor quality or incorrect
  • KTM 690 enduro fuel pressure regulator trouble
  • KTM 690 enduro fuel pressure too low or too high
  • KTM 690 enduro fuel pump bearings may wear. Replace the fuel pump
  • KTM 690 enduro fuel pump not operating
  • KTM 690 enduro fuel pump operates intermittently and often DFI fuse blows
  • KTM 690 enduro fuel pump relay trouble
  • KTM 690 enduro fuel pump trouble
  • KTM 690 enduro fuel/air mixture incorrect
  • KTM 690 enduro fuel/air mixture incorrect
  • KTM 690 enduro gear position sensor, starter lockout or side stand switch trouble
  • KTM 690 enduro inspect and repair or replace
  • KTM 690 enduro intake air pressure sensor trouble
  • KTM 690 enduro intake air temperature sensor trouble
  • KTM 690 enduro intake air temperature sensor trouble
  • KTM 690 enduro intermittent any DFI fault and its recovery
  • KTM 690 enduro little fuel in tank
  • KTM 690 enduro main throttle sensor trouble
  • KTM 690 enduro no or little fuel in tank
  • KTM 690 enduro poor acceleration
  • KTM 690 enduro spark plug burned or gap maladjusted
  • KTM 690 enduro spark plug dirty, broken or gap maladjusted
  • KTM 690 enduro spark plug incorrect
  • KTM 690 enduro spark weak
  • KTM 690 enduro stick coil shorted or not in good contact
  • KTM 690 enduro stick coil trouble
  • KTM 690 enduro subthrottle sensor trouble
  • KTM 690 enduro subthrottle valve actuator trouble
  • KTM 690 enduro throttle body assy dust seal damage
  • KTM 690 enduro throttle body assy holder loose
  • KTM 690 enduro throttle valves will not fully open
  • KTM 690 enduro unstable (rough) idling
  • KTM 690 enduro unstable fuel pressure
  • KTM 690 enduro vacuum hose
  • KTM 690 enduro vehicle-down sensor trouble
  • KTM 690 enduro water or foreign matter in fuel Change fuel
  • KTM 690 enduro water temperature sensor trouble

Your motorcycle engine consists of a lot of parts such as the engine block, cylinder heads and pistons. It is important to make sure these are all clean and lubricated to avoid engine problems. Also remember that KTM 690 Enduro motorcycle engine is a very delicate piece of machinery so it's best to handle it with care.

Possible Failure Types :

  • Strange KTM 690 Enduro engine noise.
  • KTM 690 Enduro fog from engine.
  • Strange KTM 690 Enduro engine noise.
  • KTM 690 Enduro Vibrations and Rattling
  • KTM 690 Enduro Loud Acceleration
  • KTM 690 Enduro rusty exhaust
  • KTM 690 Enduro blockages in exhaust pipe
  • KTM 690 Enduro wear and tear exhaust
KTM Logo

Through a very complicated series of events, the informal company started in Mattighofen, Austria in 1934 became KTM AG in 1992. KTM is now one of the largest European producers of motorcycles, and are world-famous for their nearly indestructible off-road and adventure bikes.

Check other KTM fault codes.

Common abbreviations and their meanings below:

ABS: Anti-Lock Braking System
ACR: Automatic Compression Release
AFR: Air Fuel Ratio
AIS: Active Intake Solenoid
ATS: Air Temperature Sensor
BAS: Bank Angle Sensor
BCM: Body Control Module
CAN: Controller Area Network
CCM: Cruise Control Module
CKP: Crank Position Sensor
DLC: Datalink Connector
DTC: Diagnostic Trouble Codes
ECM: Electronic Control Module
ECT: Engine Coolant Temperature
ECU: Electronic Control Unit
EFI: Electronic Fuel Injection
EFP: Electronic Fuel Pump
ET: Engine Temperature sensor
FI: Fuel Injectors
FPR: Fuel Pressure Regulator
H-DSSS: Harley-Davidson® Smart Security System
HCU: Hydraulic Control Unit, ABS
HFSM: Hands Free Security Module
HO2S: Heated Oxygen Sensor
IAC: Idle Air Control actuator
IAT: Intake Air Temperature sensor
ICM: Ignition Control Module
IMAP: MAP + IAT in one unit
ISS: Ion Sensing System
JSS: Jiffy Stand Sensor
LHCM: Left Hand Control Module
MAP: Manifold Absolute Pressure sensor
MHR: Right Hand Control Module
RCM: Reverse Control Module
TCA: Throttle Control Actuator
TGS: Twist Grip Sensor
TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment
TPS: Throttle Position Sensor
TSM / TSSM: (Turn Signal / Turn Signal Security Module)
VE: Volume Efficiency
VIN: Vehicle Identification Number
VSS: Vehicle Speed Sensor
WSS: Wheel Speed Sensor

These abbreviations, and the accompanying list of trouble codes, can be a great start when your KTM check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.

KTM and logo are registered trademarks of KTM. We are fan of MOTORCYCLES ! We love them.

Motorcycle electrical systems are very complex to fix it, check with your motorcycle diagnosis tool for the fault code and start motorcycle troubleshooting process.Some bike problems require professional troubleshooting and repair. However, there are many issues that you can easily fix on your own.

About Us | Contact | Privacy

Copyright 2022 - © MotorcycleTroubleshooting.com