KTM 85 Supermoto Fault Codes
KTM 85 Supermoto motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following ktm 85 supermoto faults are the list of some of the parts of a motorcycle engine.
To fix the issue of fault codes, you’ll need to disconnect the battery cable. This will ensure that you don’t get shocked while handling the terminals. Next, you will want to clean them with a soft brush and water to get rid of the corrosion. Once KTM 85 Supermoto is cleaned properly, you can put them back on the terminal and reattach the cable.
KTM 85 Supermoto Faults :
Engine management systems of KTM 85 Supermoto are responsible for monitoring a range of features and its warning light should go out a few seconds after ignition. The system's main job is to keep the engine running at peak performance by monitoring many parameters like coolant temperature, oil pressure, fuel level and air/fuel ratio. The system monitors these parameters continuously and alerts the driver if any of these parameters fall outside the predetermined limits.
KTM Motorcycle Engine Fault Codes :
| Code | Description |
|---|---|
| Constant | Tilt Sensor - input signal too high |
| Constant | Tilt Sensor - input signal too low |
| 2 | Crankshaft speed sensor - synchronization faulty |
| 2 | Crankshaft speed sensor - signal implausible |
| 2 | Crankshaft speed sensor - signal irregular |
| 2 | Crankshaft speed sensor - no signal |
| 6 | Throttle valve position sensor circuit A - adaption failed |
| 6 | Throttle valve position sensor circuit A - input signal too low |
| 6 | Throttle valve position sensor circuit A - input signal too high |
| 9 | Crankcase pressure sensor - short circuit to ground |
| 9 | Crankcase pressure sensor - open / short to plus |
| 9 | Ambient air pressure sensor - short circuit to ground |
| 9 | Ambient air pressure sensor - open / short circuit to plus |
| 12 | Coolant temperature sensor - input signal too low |
| 12 | Coolant temperature sensor - input signal too high |
| 13 | Intake air temperature sensor - input signal too low |
| 13 | Intake air temperature sensor - input signal too high |
| 14 | Crankcae pressure sensor - difference too high between sensor and engine ECU |
| 21 | Battery voltage - input voltage too low |
| 21 | Battery voltage - input voltage too high |
| 33 | Injection valve 0, cylinder 1- input signal too low |
| 33 | Injection valve 0, cylinder 1- input signal too high |
| 34 | Injection valve 1, cylinder 1- input signal too low |
| 34 | Injection valve 1, cylinder 1- input signal too high |
| 37 | Ignition coil - circuit fault |
| 41 | Fuel pump - short circuit to ground / open circuit |
| 41 | Fuel pump - open circuit / short circuit to plus |
| 42 | Oil pump - input signal too low |
| 42 | Oil pump - signal too high |
KTM Flash Codes :
Blink code of FI warning lamp (MIL) 02 FI warning lamp (MIL) flashes 2x short Error level condition Crankshaft position sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 06 FI warning lamp (MIL) flashes 6x short Error level condition Throttle position sensor circuit A - input signal too low Throttle position sensor circuit A - input signal too high Blink code of FI warning lamp (MIL) 09 FI warning lamp (MIL) flashes 9x short Error level condition Manifold absolute pressure sensor - input signal too low Manifold absolute pressure sensor - input signal too high Blink code of FI warning lamp (MIL) 11 FI warning lamp (MIL) flashes 1x long, 1x short Error level condition Idle control - engine speed below target value Idle control - engine speed above target value Blink code of FI warning lamp (MIL) 12 FI warning lamp (MIL) flashes 1x long, 2x short Error level condition Engine coolant temperature sensor - input signal too low Engine coolant temperature sensor - input signal too high 22 FLASH CODE 173 Blink code of FI warning lamp (MIL) 13 FI warning lamp (MIL) flashes 1x long, 3x short Error level condition Intake air temperature sensor - input signal too low Intake air temperature sensor - input signal too high Blink code of FI warning lamp (MIL) 14 FI warning lamp (MIL) flashes 1x long, 4x short Error level condition Fuel tank sensor - circuit fault Fuel tank sensor - short circuit to ground Fuel tank sensor - short circuit to plus Blink code of FI warning lamp (MIL) 15 FI warning lamp (MIL) flashes 1x long, 5x short Error level condition Rollover sensor - plausibility Rollover sensor - circuit fault Rollover sensor - short circuit to ground Rollover sensor - short circuit to plus Blink code of FI warning lamp (MIL) 16 FI warning lamp (MIL) flashes 1x long, 6x short Error level condition Radiator fan motor - circuit fault Radiator fan motor - input signal too low Radiator fan motor - input signal too high 22 FLASH CODE 174 Blink code of FI warning lamp (MIL) 17 FI warning lamp (MIL) flashes 1x long, 7x short Error level condition Lambda sensor - circuit fault Lambda sensor - input signal too low Lambda sensor - input signal too high Lambda sensor - no function Blink code of FI warning lamp (MIL) 18 FI warning lamp (MIL) flashes 1x long, 8x short Error level condition Engine diagnosis warning lamp (MIL) - circuit fault Engine diagnosis warning lamp (MIL) - short circuit to ground Engine diagnosis warning lamp (MIL) - short circuit to plus Blink code of FI warning lamp (MIL) 19 FI warning lamp (MIL) flashes 1x long, 9x short Error level condition Fuel pump lamp - circuit fault Low fuel warning lamp - input signal too low Low fuel warning lamp - input signal too high Blink code of FI warning lamp (MIL) 21 FI warning lamp (MIL) flashes 2x long, 1x short Error level condition Engine control relay - switch-off delay 22 FLASH CODE 175 Blink code of FI warning lamp (MIL) 22 FI warning lamp (MIL) flashes 2x long, 2x short Error level condition Engine speed signal - circuit fault Engine speed signal - input signal too low Engine speed signal - input signal too high Blink code of FI warning lamp (MIL) 23 FI warning lamp (MIL) flashes 2x long, 3x short Error level condition Travel speed sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 24 FI warning lamp (MIL) flashes 2x long, 4x short Error level condition System voltage - too low System voltage - too high System voltage - implausible value Blink code of FI warning lamp (MIL) 25 FI warning lamp (MIL) flashes 2x long, 5x short Error level condition Side stand switch - plausibility Side stand switch - circuit fault Side stand switch - short circuit to ground Side stand switch - short circuit to plus 22 FLASH CODE 176 Blink code of FI warning lamp (MIL) 26 FI warning lamp (MIL) flashes 2x long, 6x short Error level condition Sensor A reference voltage - input signal too low Sensor A reference voltage - input signal too high Blink code of FI warning lamp (MIL) 27 FI warning lamp (MIL) flashes 2x long, 7x short Error level condition Sensor B reference voltage - input signal too low Sensor B reference voltage - input signal too high Blink code of FI warning lamp (MIL) 33 FI warning lamp (MIL) flashes 3x long, 3x short Error level condition Injector - circuit fault Injector - input signal too low Injector - input signal too high Blink code of FI warning lamp (MIL) 41 FI warning lamp (MIL) flashes 4x long, 1x short Error level condition Fuel pump relay - circuit fault Fuel pump relay - input signal too low Fuel pump relay - input signal too high 22 FLASH CODE 177 Blink code of FI warning lamp (MIL) 45 FI warning lamp (MIL) flashes 4x long, 5x short Error level condition Lambda sensor heater - circuit fault Lambda sensor heater - short circuit to ground or open circuit Lambda sensor heater - input signal too high Blink code of FI warning lamp (MIL) 49 FI warning lamp (MIL) flashes 4x long, 9x short Error level condition Idle control - input signal too low Idle control - input signal too high Idle control - circuit fault
KTM 85 Supermoto Motorcycle Problems :
- KTM 85 supermoto after fire
- KTM 85 supermoto air cleaner clogged, poorly sealed, or missing
- KTM 85 supermoto air cleaner element clogged
- KTM 85 supermoto air duct loose
- KTM 85 supermoto air suction valve trouble
- KTM 85 supermoto air switching valve trouble
- KTM 85 supermoto backfiring when deceleration
- KTM 85 supermoto cracked or obstructed intake air pressure sensor
- KTM 85 supermoto crankshaft sensor trouble
- KTM 85 supermoto eCU ground and power supply trouble
- KTM 85 supermoto eCU trouble
- KTM 85 supermoto engine overheating - Water temperature sensor or crankshaft sensor trouble
- KTM 85 supermoto engine stalls easily
- KTM 85 supermoto engine vacuum not synchronizing
- KTM 85 supermoto exhaust Smokes Excessively
- KTM 85 supermoto firing incorrect
- KTM 85 supermoto fuel filter clogged
- KTM 85 supermoto fuel injector clogged
- KTM 85 supermoto fuel injector O-ring damage
- KTM 85 supermoto fuel injector trouble
- KTM 85 supermoto fuel line clogged
- KTM 85 supermoto fuel poor quality or incorrect
- KTM 85 supermoto fuel pressure regulator trouble
- KTM 85 supermoto fuel pressure too low or too high
- KTM 85 supermoto fuel pump bearings may wear. Replace the fuel pump
- KTM 85 supermoto fuel pump not operating
- KTM 85 supermoto fuel pump operates intermittently and often DFI fuse blows
- KTM 85 supermoto fuel pump relay trouble
- KTM 85 supermoto fuel pump trouble
- KTM 85 supermoto fuel/air mixture incorrect
- KTM 85 supermoto fuel/air mixture incorrect
- KTM 85 supermoto gear position sensor, starter lockout or side stand switch trouble
- KTM 85 supermoto inspect and repair or replace
- KTM 85 supermoto intake air pressure sensor trouble
- KTM 85 supermoto intake air temperature sensor trouble
- KTM 85 supermoto intake air temperature sensor trouble
- KTM 85 supermoto intermittent any DFI fault and its recovery
- KTM 85 supermoto little fuel in tank
- KTM 85 supermoto main throttle sensor trouble
- KTM 85 supermoto no or little fuel in tank
- KTM 85 supermoto poor acceleration
- KTM 85 supermoto spark plug burned or gap maladjusted
- KTM 85 supermoto spark plug dirty, broken or gap maladjusted
- KTM 85 supermoto spark plug incorrect
- KTM 85 supermoto spark weak
- KTM 85 supermoto stick coil shorted or not in good contact
- KTM 85 supermoto stick coil trouble
- KTM 85 supermoto subthrottle sensor trouble
- KTM 85 supermoto subthrottle valve actuator trouble
- KTM 85 supermoto throttle body assy dust seal damage
- KTM 85 supermoto throttle body assy holder loose
- KTM 85 supermoto throttle valves will not fully open
- KTM 85 supermoto unstable (rough) idling
- KTM 85 supermoto unstable fuel pressure
- KTM 85 supermoto vacuum hose
- KTM 85 supermoto vehicle-down sensor trouble
- KTM 85 supermoto water or foreign matter in fuel Change fuel
- KTM 85 supermoto water temperature sensor trouble
The electrical system includes the battery, the charging system, the starters, and also the charging system. it's conjointly attainable that the electrical system will fail thanks to a tangle with the generator. an honest place to begin troubleshooting the electrical system is to see the engine elements. for instance, it's attainable that the electrical system will fail thanks to a tangle with the generator. an honest place to begin troubleshooting the electrical system is to see the engine elements.
Possible Failure Types :
- Strange KTM 85 Supermoto engine noise.
- KTM 85 Supermoto fog from engine.
- Strange KTM 85 Supermoto engine noise.
- KTM 85 Supermoto Vibrations and Rattling
- KTM 85 Supermoto Loud Acceleration
- KTM 85 Supermoto rusty exhaust
- KTM 85 Supermoto blockages in exhaust pipe
- KTM 85 Supermoto wear and tear exhaust
Through a very complicated series of events, the informal company started in Mattighofen, Austria in 1934 became KTM AG in 1992. KTM is now one of the largest European producers of motorcycles, and are world-famous for their nearly indestructible off-road and adventure bikes.
Check other KTM fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your KTM check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
KTM and logo are registered trademarks of KTM. We are fan of MOTORCYCLES ! We love them.