KTM GO 50 Fault Codes
KTM GO 50 motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following ktm go 50 faults are the list of some of the parts of a motorcycle engine.
The oil level of KTM GO 50 should be the same level in the dipstick, even when the engine is cold. You can check the oil level by removing the dipstick, holding the dipstick in your hand, and then reinserting the dipstick. Then, you’ll be able to see where the oil level is.
KTM GO 50 Faults :
Engine management systems of KTM GO 50 are responsible for monitoring a range of features and its warning light should go out a few seconds after ignition. The system's main job is to keep the engine running at peak performance by monitoring many parameters like coolant temperature, oil pressure, fuel level and air/fuel ratio. The system monitors these parameters continuously and alerts the driver if any of these parameters fall outside the predetermined limits.
KTM Motorcycle Engine Fault Codes :
| Code | Description |
|---|---|
| Constant | Tilt Sensor - input signal too high |
| Constant | Tilt Sensor - input signal too low |
| 2 | Crankshaft speed sensor - synchronization faulty |
| 2 | Crankshaft speed sensor - signal implausible |
| 2 | Crankshaft speed sensor - signal irregular |
| 2 | Crankshaft speed sensor - no signal |
| 6 | Throttle valve position sensor circuit A - adaption failed |
| 6 | Throttle valve position sensor circuit A - input signal too low |
| 6 | Throttle valve position sensor circuit A - input signal too high |
| 9 | Crankcase pressure sensor - short circuit to ground |
| 9 | Crankcase pressure sensor - open / short to plus |
| 9 | Ambient air pressure sensor - short circuit to ground |
| 9 | Ambient air pressure sensor - open / short circuit to plus |
| 12 | Coolant temperature sensor - input signal too low |
| 12 | Coolant temperature sensor - input signal too high |
| 13 | Intake air temperature sensor - input signal too low |
| 13 | Intake air temperature sensor - input signal too high |
| 14 | Crankcae pressure sensor - difference too high between sensor and engine ECU |
| 21 | Battery voltage - input voltage too low |
| 21 | Battery voltage - input voltage too high |
| 33 | Injection valve 0, cylinder 1- input signal too low |
| 33 | Injection valve 0, cylinder 1- input signal too high |
| 34 | Injection valve 1, cylinder 1- input signal too low |
| 34 | Injection valve 1, cylinder 1- input signal too high |
| 37 | Ignition coil - circuit fault |
| 41 | Fuel pump - short circuit to ground / open circuit |
| 41 | Fuel pump - open circuit / short circuit to plus |
| 42 | Oil pump - input signal too low |
| 42 | Oil pump - signal too high |
KTM Flash Codes :
Blink code of FI warning lamp (MIL) 02 FI warning lamp (MIL) flashes 2x short Error level condition Crankshaft position sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 06 FI warning lamp (MIL) flashes 6x short Error level condition Throttle position sensor circuit A - input signal too low Throttle position sensor circuit A - input signal too high Blink code of FI warning lamp (MIL) 09 FI warning lamp (MIL) flashes 9x short Error level condition Manifold absolute pressure sensor - input signal too low Manifold absolute pressure sensor - input signal too high Blink code of FI warning lamp (MIL) 11 FI warning lamp (MIL) flashes 1x long, 1x short Error level condition Idle control - engine speed below target value Idle control - engine speed above target value Blink code of FI warning lamp (MIL) 12 FI warning lamp (MIL) flashes 1x long, 2x short Error level condition Engine coolant temperature sensor - input signal too low Engine coolant temperature sensor - input signal too high 22 FLASH CODE 173 Blink code of FI warning lamp (MIL) 13 FI warning lamp (MIL) flashes 1x long, 3x short Error level condition Intake air temperature sensor - input signal too low Intake air temperature sensor - input signal too high Blink code of FI warning lamp (MIL) 14 FI warning lamp (MIL) flashes 1x long, 4x short Error level condition Fuel tank sensor - circuit fault Fuel tank sensor - short circuit to ground Fuel tank sensor - short circuit to plus Blink code of FI warning lamp (MIL) 15 FI warning lamp (MIL) flashes 1x long, 5x short Error level condition Rollover sensor - plausibility Rollover sensor - circuit fault Rollover sensor - short circuit to ground Rollover sensor - short circuit to plus Blink code of FI warning lamp (MIL) 16 FI warning lamp (MIL) flashes 1x long, 6x short Error level condition Radiator fan motor - circuit fault Radiator fan motor - input signal too low Radiator fan motor - input signal too high 22 FLASH CODE 174 Blink code of FI warning lamp (MIL) 17 FI warning lamp (MIL) flashes 1x long, 7x short Error level condition Lambda sensor - circuit fault Lambda sensor - input signal too low Lambda sensor - input signal too high Lambda sensor - no function Blink code of FI warning lamp (MIL) 18 FI warning lamp (MIL) flashes 1x long, 8x short Error level condition Engine diagnosis warning lamp (MIL) - circuit fault Engine diagnosis warning lamp (MIL) - short circuit to ground Engine diagnosis warning lamp (MIL) - short circuit to plus Blink code of FI warning lamp (MIL) 19 FI warning lamp (MIL) flashes 1x long, 9x short Error level condition Fuel pump lamp - circuit fault Low fuel warning lamp - input signal too low Low fuel warning lamp - input signal too high Blink code of FI warning lamp (MIL) 21 FI warning lamp (MIL) flashes 2x long, 1x short Error level condition Engine control relay - switch-off delay 22 FLASH CODE 175 Blink code of FI warning lamp (MIL) 22 FI warning lamp (MIL) flashes 2x long, 2x short Error level condition Engine speed signal - circuit fault Engine speed signal - input signal too low Engine speed signal - input signal too high Blink code of FI warning lamp (MIL) 23 FI warning lamp (MIL) flashes 2x long, 3x short Error level condition Travel speed sensor - measurement range or power problem Blink code of FI warning lamp (MIL) 24 FI warning lamp (MIL) flashes 2x long, 4x short Error level condition System voltage - too low System voltage - too high System voltage - implausible value Blink code of FI warning lamp (MIL) 25 FI warning lamp (MIL) flashes 2x long, 5x short Error level condition Side stand switch - plausibility Side stand switch - circuit fault Side stand switch - short circuit to ground Side stand switch - short circuit to plus 22 FLASH CODE 176 Blink code of FI warning lamp (MIL) 26 FI warning lamp (MIL) flashes 2x long, 6x short Error level condition Sensor A reference voltage - input signal too low Sensor A reference voltage - input signal too high Blink code of FI warning lamp (MIL) 27 FI warning lamp (MIL) flashes 2x long, 7x short Error level condition Sensor B reference voltage - input signal too low Sensor B reference voltage - input signal too high Blink code of FI warning lamp (MIL) 33 FI warning lamp (MIL) flashes 3x long, 3x short Error level condition Injector - circuit fault Injector - input signal too low Injector - input signal too high Blink code of FI warning lamp (MIL) 41 FI warning lamp (MIL) flashes 4x long, 1x short Error level condition Fuel pump relay - circuit fault Fuel pump relay - input signal too low Fuel pump relay - input signal too high 22 FLASH CODE 177 Blink code of FI warning lamp (MIL) 45 FI warning lamp (MIL) flashes 4x long, 5x short Error level condition Lambda sensor heater - circuit fault Lambda sensor heater - short circuit to ground or open circuit Lambda sensor heater - input signal too high Blink code of FI warning lamp (MIL) 49 FI warning lamp (MIL) flashes 4x long, 9x short Error level condition Idle control - input signal too low Idle control - input signal too high Idle control - circuit fault
KTM GO 50 Motorcycle Problems :
- KTM go 50 after fire
- KTM go 50 air cleaner clogged, poorly sealed, or missing
- KTM go 50 air cleaner element clogged
- KTM go 50 air duct loose
- KTM go 50 air suction valve trouble
- KTM go 50 air switching valve trouble
- KTM go 50 backfiring when deceleration
- KTM go 50 cracked or obstructed intake air pressure sensor
- KTM go 50 crankshaft sensor trouble
- KTM go 50 eCU ground and power supply trouble
- KTM go 50 eCU trouble
- KTM go 50 engine overheating - Water temperature sensor or crankshaft sensor trouble
- KTM go 50 engine stalls easily
- KTM go 50 engine vacuum not synchronizing
- KTM go 50 exhaust Smokes Excessively
- KTM go 50 firing incorrect
- KTM go 50 fuel filter clogged
- KTM go 50 fuel injector clogged
- KTM go 50 fuel injector O-ring damage
- KTM go 50 fuel injector trouble
- KTM go 50 fuel line clogged
- KTM go 50 fuel poor quality or incorrect
- KTM go 50 fuel pressure regulator trouble
- KTM go 50 fuel pressure too low or too high
- KTM go 50 fuel pump bearings may wear. Replace the fuel pump
- KTM go 50 fuel pump not operating
- KTM go 50 fuel pump operates intermittently and often DFI fuse blows
- KTM go 50 fuel pump relay trouble
- KTM go 50 fuel pump trouble
- KTM go 50 fuel/air mixture incorrect
- KTM go 50 fuel/air mixture incorrect
- KTM go 50 gear position sensor, starter lockout or side stand switch trouble
- KTM go 50 inspect and repair or replace
- KTM go 50 intake air pressure sensor trouble
- KTM go 50 intake air temperature sensor trouble
- KTM go 50 intake air temperature sensor trouble
- KTM go 50 intermittent any DFI fault and its recovery
- KTM go 50 little fuel in tank
- KTM go 50 main throttle sensor trouble
- KTM go 50 no or little fuel in tank
- KTM go 50 poor acceleration
- KTM go 50 spark plug burned or gap maladjusted
- KTM go 50 spark plug dirty, broken or gap maladjusted
- KTM go 50 spark plug incorrect
- KTM go 50 spark weak
- KTM go 50 stick coil shorted or not in good contact
- KTM go 50 stick coil trouble
- KTM go 50 subthrottle sensor trouble
- KTM go 50 subthrottle valve actuator trouble
- KTM go 50 throttle body assy dust seal damage
- KTM go 50 throttle body assy holder loose
- KTM go 50 throttle valves will not fully open
- KTM go 50 unstable (rough) idling
- KTM go 50 unstable fuel pressure
- KTM go 50 vacuum hose
- KTM go 50 vehicle-down sensor trouble
- KTM go 50 water or foreign matter in fuel Change fuel
- KTM go 50 water temperature sensor trouble
Issues with the engine area unit generally caused by problems with the engine elements. whether or not it's a fuel issue or AN ignition drawback, the engine elements ought to be inspected to work out the cause. Another issue that may occur is once the bike engine isn't operating could be a failure of the electrical system. this will cause the bike to stall and not work properly. The KTM GO 50 electrical system is often the foremost complicated system on a motorbike.
Possible Failure Types :
- Strange KTM GO 50 engine noise.
- KTM GO 50 fog from engine.
- Strange KTM GO 50 engine noise.
- KTM GO 50 Vibrations and Rattling
- KTM GO 50 Loud Acceleration
- KTM GO 50 rusty exhaust
- KTM GO 50 blockages in exhaust pipe
- KTM GO 50 wear and tear exhaust
Through a very complicated series of events, the informal company started in Mattighofen, Austria in 1934 became KTM AG in 1992. KTM is now one of the largest European producers of motorcycles, and are world-famous for their nearly indestructible off-road and adventure bikes.
Check other KTM fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your KTM check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
KTM and logo are registered trademarks of KTM. We are fan of MOTORCYCLES ! We love them.