Triumph Trophy Fault Codes
Triumph Trophy motorcycles have engines, which are made up of many different parts. These parts must work together in order for the engine to function. A problem with one of the parts can make the engine not run. There are many different parts that make up an engine. The following triumph trophy faults are the list of some of the parts of a motorcycle engine.
The oil level of Triumph Trophy should be the same level in the dipstick, even when the engine is cold. You can check the oil level by removing the dipstick, holding the dipstick in your hand, and then reinserting the dipstick. Then, you’ll be able to see where the oil level is.
Triumph Trophy Faults :
Another drawback that may occur along with your bike engine could be a blown gasket. this will cause your engine to overheat and presumably crack the cylinder heads. during this case, it's best to require your Triumph Trophy bike to an expert mechanic to possess it verified. Another common drawback is with the carburettor. The carburettor is that the a part of your bike that mixes air and fuel to make the combustion required to power the engine.
Diagnostic trouble codes (DTCs) are logged in the ECM memory when there is a confirmed fault in the system & are reported as a four digit code. The system will log the diagnostic trouble codes listed below (not all are applicable to every model).
When the system detects a fault, it begins to count the number of times the fault occurs before illuminating the MIL and storing a fault code. Similarly, if a fault clears, the ECM also records this fact and will turn off the MIL when sufficient no-fault warm-up cycles have taken place. Any fault codes will remain in the ECM memory until the required number of no-fault warm-up cycles have taken place. The number of warm-up cycles required to extinguish the MIL will always be less than the number required to remove a DTC from the ECM memory.
Triumph Motorcycle Troubleshooting :
Symptom | Possible Causes | Action |
---|---|---|
Test is aborted immediately after clicking Start. | Transmission is not in neutral. Neutral position is not adapted. Neutral position adaption is in a state of error. | Check the transmission is in neutral. Reset the neutral position adaption. Start the engine and allow the neutral position to adapt. Turn the ignition off for at least 60 seconds before restarting the crankshaft position adaption test. |
Test is aborted after the engine has reached the required temperature. | The throttle was not held open within 60 seconds of the engine reaching the required temperature. | Turn the ignition off for at least 60 seconds before restarting the crankshaft position adaption test. Make sure the throttle is held open within 60 seconds of being instructed to do so by the diagnostic tool. |
Crank adaption failed. Throttle was held fully open for 10 seconds before the diagnostic tool displayed an instruction to close the throttle. | Ignition was not turned off for 60 seconds after adapting the neutral position. | Turn the ignition off for at least 60 seconds before restarting the crankshaft position adaption test. |
Crank adaption failed. The diagnostic tool displayed an instruction to close the throttle at the expected time (after the forth engine revving cycle). | Adaption has completed abnormally. Mechanical fault. Crankshaft position signal out of range. Crankshaft trigger wheel out of tolerance. | Investigate potential mechanical faults. Contact Triumph Service. |
Triumph Fault Codes List:
Diagnostic Trouble Code (DTC) | Fault Description | Number of no-fault cycles before turning off MIL | Number of no-fault cycles before DTC is erased | MIL illuminated when fault is logged |
---|---|---|---|---|
P0031 | Oxygen sensor heater open circuit or short to ground | 3 | 40 | Yes |
P0032 | Oxygen sensor heater short circuit to vBatt | 3 | 40 | Yes |
P0107 | Manifold absolute pressure sensor 1 short circuit to ground | 3 | 40 | Yes |
P0108 | Manifold absolute pressure sensor 1 open circuit or short circuit to 5 Volt sensor supply | 3 | 40 | Yes |
P0112 | Intake air temperature sensor short circuit to ground | 3 | 40 | Yes |
P0113 | Intake air temperature sensor open circuit or short circuit to 5 Volt sensor supply | 3 | 40 | Yes |
P0117 | Engine coolant temperature sensor short circuit to ground | 3 | 40 | Yes |
P0118 | Engine coolant temperature sensor open circuit or short circuit to 5 Volt sensor supply | 3 | 40 | Yes |
P0122 | Throttle position sensor 1 short circuit to ground or open circuit | 3 | 40 | Yes |
P0123 | Throttle position sensor 1 short circuit to vBatt | 3 | 40 | Yes |
P0130 | Oxygen sensor circuit malfunction | 3 | 40 | Yes |
P0201 | Injector 1 circuit malfunction | 3 | 40 | Yes |
P0202 | Injector 2 circuit malfunction | 3 | 40 | Yes |
P0203 | Injector 3 circuit malfunction | 3 | 40 | Yes |
P0227 | Throttle position sensor 2 short circuit to ground or open circuit | 3 | 40 | Yes |
P0228 | Throttle position sensor 2 short circuit to vBatt | 3 | 40 | Yes |
P0335 | Crankshaft sensor circuit malfunction | 3 | 40 | Yes |
P0351 | Ignition coil fault - coil 1 | 3 | 40 | Yes |
P0352 | Ignition coil fault - coil 2 | 3 | 40 | Yes |
P0353 | Ignition coil fault - coil 3 | 3 | 40 | Yes |
P0413 | Secondary air injection system short circuit to ground or open circuit | 3 | 40 | Yes |
P0414 | Secondary air injection system short circuit to vBatt | 3 | 40 | Yes |
P0444 | Purge valve system short circuit to ground or open circuit | 0 | 40 | No |
P0445 | Purge valve short circuit to vBatt or over temp | 3 | 40 | Yes |
P0460 | Fuel level sensor circuit malfunction | 3 | 40 | Yes |
P0500 | Vehicle speed sensor malfunction | 3 | 40 | Yes |
P0505 | Idle speed control motor / air valve malfunction | 3 | 40 | Yes |
P0510 | Cruise cancel switch malfunction | 3 | 40 | Yes |
P0560 | System Voltage - battery circuit malfunction | 3 | 40 | Yes |
P0571 | Brake 1 switch malfunction | 3 | 40 | Yes |
P0603 | EEPROM error | 0 | 40 | No |
P0616 | Starter relay short circuit to ground or open circuit | 3 | 40 | Yes |
P0617 | Starter motor relay short circuit to vBatt | 3 | 40 | Yes |
P0654 | Tachometer circuit malfunction (supported by DTC P1690) | 0 | 40 | No |
P0705 | Gear position sensor circuit malfunction | 3 | 40 | Yes |
P1105 | Manifold absolute pressure sensor 1 pipe malfunction | 3 | 40 | Yes |
P1107 | Ambient pressure sensor circuit short circuit to ground | 3 | 40 | Yes |
P1108 | Ambient air pressure sensor circuit open circuit or short circuit to 5 Volt sensor supply | 3 | 40 | Yes |
P1115 | Coolant temperature gauge circuit malfunction (supported by DTC P1690) | 0 | 40 | No |
P1135 | Traction Control prevented due to ABS problem | 3 | 40 | Yes |
P1231 | Fuel pump relay short circuit to ground or open circuit | 3 | 40 | Yes |
P1232 | Fuel pump relay short circuit to vBatt | 3 | 40 | Yes |
P1500 | Vehicle speed output circuit malfunction (supported by DTC P1690) | 0 | 40 | No |
P1508 | Unmatched Immobiliser ECM | 3 | 40 | Flashing |
P1520 | Unmatched ABS | 3 | 40 | Flashing |
P1521 | Lost communication with ABS | 3 | 40 | Yes |
P1534 | Engine oil level sensor circuit malfunction | 3 | 40 | Yes |
P1552 | Cooling fan relay short circuit or open circuit | 3 | 40 | Yes |
P1553 | Cooling fan relay short to battery vBatt or over temperature | 3 | 40 | Yes |
P1571 | Brake 2 switch malfunction | 3 | 40 | Yes |
P1574 | Cruise control prevented due to other malfunction condition | 3 | 40 | Yes |
P1575 | Cruise control disabled until button press sequence completed | 3 | 40 | Yes |
P1576 | Brake 1 switch correlation error with brake switch 2 | 3 | 40 | Yes |
P1577 | Brake 2 switch correlation error with brake switch 1 | 3 | 40 | Yes |
P1604 | ECM tamper detected - return to Triumph | 0 | 0 | Yes |
P1605 | ECM locked by the tunelock function | Only if Tunelock is unlocked | N/A | Flashing |
P1606 | ECM internal error | 3 | 40 | Yes |
P1607 | ECM ride by wire internal error | 3 | 40 | Yes |
P1608 | ECM ride by wire internal error | 3 | 40 | Yes |
P1620 | Headlamp relay short circuit to vBatt | 0 | 40 | No |
P1631 | Fall detection circuit short circuit to ground | 3 | 40 | Yes |
P1632 | Fall detection circuit short circuit to vBatt | 3 | 40 | Yes |
P1650 | Lost communication with Immobiliser ECM | 3 | 40 | Yes |
P1659 | Ignition power supply malfunction | 0 | 40 | No |
P1685 | Main relay circuit malfunction | 3 | 40 | Yes |
P1690 | CAN fault | 3 | 40 | Yes |
P1695 | Lost communication with the instrument panel | 3 | 40 | Yes |
P1696 | 5V sensor supply short circuit to ground | 3 | 40 | Yes |
P1697 | 5V sensor supply short circuit to vBatt | 3 | 40 | Yes |
P1698 | 5V sensor supply circuit malfunction | 3 | 40 | Yes |
P2102 | Throttle actuator motor short to ground or open circuit | 3 | 40 | Yes |
P2103 | Throttle actuator motor short to vBatt | 3 | 40 | Yes |
P2107 | Throttle valve drive error | 3 | 40 | Yes |
P2111 | Throttle valve drive error | 3 | 40 | Yes |
P2119 | Throttle valve drive error | 3 | 40 | Yes |
P2122 | Twist grip position sensor 1 short circuit to ground or open circuit | 3 | 40 | Yes |
P1614 | Instrument ID incompatible | 3 | 40 | No |
P1616 | Accessory control relay short circuit to ground or open circuit | 0 | 40 | No |
P1617 | Accessory control relay short circuit to vBatt | 0 | 40 | No |
P1619 | Headlamp relay short circuit to ground or open circuit | 0 | 40 | No |
P2123 | Twist grip position sensor 1 short circuit to vBatt | 3 | 40 | Yes |
P2127 | Twist grip position sensor 2 short circuit to ground or open circuit | 3 | 40 | Yes |
P2128 | Twist grip position sensor 2 short to vBatt | 3 | 40 | Yes |
P2136 | Throttle position sensor 1 correlation error with throttle position sensor 2 | 3 | 40 | Yes |
P2138 | Twist grip position sensor 1 correlation error with twist grip position sensor 2 | 3 | 40 | Yes |
Triumph ABS Diagnostic Trouble Codes
DTCs are logged in the ABS ECM memory when there is a confirmed fault in the system & are reported as a four digit code.
Diagnostic Trouble Code (DTC) | Fault Description |
---|---|
C1611 | Front wheel sensor short circuit to ground or open circuit |
C1612 | Front wheel sensor abnormal input or dropping out |
C1613 | Rear wheel sensor short circuit to ground or open circuit |
C1614 | Rear wheel sensor abnormal input or dropping out |
C1621 | Front wheel pulser gear missing teeth |
C1623 | Rear wheel pulser gear missing teeth |
C1631 | Front wheel input solenoid short circuit to ground or open circuit |
C1632 | Front wheel output solenoid short circuit to ground or open circuit |
C1633 | Rear wheel input solenoid short circuit to ground or open circuit |
C1634 | Rear wheel output solenoid short circuit to ground or open circuit |
C1641 | Front Wheel Actuator (Hydraulic Control) Wheel Lock |
C1643 | Rear Wheel Actuator (Hydraulic Control) Wheel Lock |
C1651 | Motor - Lock |
C1652 | Motor - Stick at OFF |
C1653 | Motor - Stick at ON |
C1654 | Solenoid relay - stick at OFF and ON |
C1661 | Power Source Voltage Drop |
C1662 | Power Source Voltage Rise |
C1671 | Different Tyre DiameterC1681 Abnormal ECU |
Triumph Trophy Motorcycle Problems :
- Triumph trophy after fire
- Triumph trophy air cleaner clogged, poorly sealed, or missing
- Triumph trophy air cleaner element clogged
- Triumph trophy air duct loose
- Triumph trophy air suction valve trouble
- Triumph trophy air switching valve trouble
- Triumph trophy backfiring when deceleration
- Triumph trophy cracked or obstructed intake air pressure sensor
- Triumph trophy crankshaft sensor trouble
- Triumph trophy eCU ground and power supply trouble
- Triumph trophy eCU trouble
- Triumph trophy engine overheating - Water temperature sensor or crankshaft sensor trouble
- Triumph trophy engine stalls easily
- Triumph trophy engine vacuum not synchronizing
- Triumph trophy exhaust Smokes Excessively
- Triumph trophy firing incorrect
- Triumph trophy fuel filter clogged
- Triumph trophy fuel injector clogged
- Triumph trophy fuel injector O-ring damage
- Triumph trophy fuel injector trouble
- Triumph trophy fuel line clogged
- Triumph trophy fuel poor quality or incorrect
- Triumph trophy fuel pressure regulator trouble
- Triumph trophy fuel pressure too low or too high
- Triumph trophy fuel pump bearings may wear. Replace the fuel pump
- Triumph trophy fuel pump not operating
- Triumph trophy fuel pump operates intermittently and often DFI fuse blows
- Triumph trophy fuel pump relay trouble
- Triumph trophy fuel pump trouble
- Triumph trophy fuel/air mixture incorrect
- Triumph trophy fuel/air mixture incorrect
- Triumph trophy gear position sensor, starter lockout or side stand switch trouble
- Triumph trophy inspect and repair or replace
- Triumph trophy intake air pressure sensor trouble
- Triumph trophy intake air temperature sensor trouble
- Triumph trophy intake air temperature sensor trouble
- Triumph trophy intermittent any DFI fault and its recovery
- Triumph trophy little fuel in tank
- Triumph trophy main throttle sensor trouble
- Triumph trophy no or little fuel in tank
- Triumph trophy poor acceleration
- Triumph trophy spark plug burned or gap maladjusted
- Triumph trophy spark plug dirty, broken or gap maladjusted
- Triumph trophy spark plug incorrect
- Triumph trophy spark weak
- Triumph trophy stick coil shorted or not in good contact
- Triumph trophy stick coil trouble
- Triumph trophy subthrottle sensor trouble
- Triumph trophy subthrottle valve actuator trouble
- Triumph trophy throttle body assy dust seal damage
- Triumph trophy throttle body assy holder loose
- Triumph trophy throttle valves will not fully open
- Triumph trophy unstable (rough) idling
- Triumph trophy unstable fuel pressure
- Triumph trophy vacuum hose
- Triumph trophy vehicle-down sensor trouble
- Triumph trophy water or foreign matter in fuel Change fuel
- Triumph trophy water temperature sensor trouble
Issues with the engine area unit generally caused by problems with the engine elements. whether or not it's a fuel issue or AN ignition drawback, the engine elements ought to be inspected to work out the cause. Another issue that may occur is once the bike engine isn't operating could be a failure of the electrical system. this will cause the bike to stall and not work properly. The Triumph Trophy electrical system is often the foremost complicated system on a motorbike.
Possible Failure Types :
- Strange Triumph Trophy engine noise.
- Triumph Trophy fog from engine.
- Strange Triumph Trophy engine noise.
- Triumph Trophy Vibrations and Rattling
- Triumph Trophy Loud Acceleration
- Triumph Trophy rusty exhaust
- Triumph Trophy blockages in exhaust pipe
- Triumph Trophy wear and tear exhaust

Triumph Motorcycles is the largest UK-owned motorcycle manufacturer in the world, after purchasing all the rights and models from the defunct Triumph Engineering. They are famous for their standard motorcycle model lines that use triple-cylinder engines, known worldwide as 'Triumph Triples' .
Check other Triumph fault codes.Common abbreviations and their meanings below:
ABS: Anti-Lock Braking System ACR: Automatic Compression Release AFR: Air Fuel Ratio AIS: Active Intake Solenoid ATS: Air Temperature Sensor BAS: Bank Angle Sensor BCM: Body Control Module CAN: Controller Area Network CCM: Cruise Control Module CKP: Crank Position Sensor DLC: Datalink Connector DTC: Diagnostic Trouble Codes ECM: Electronic Control Module ECT: Engine Coolant Temperature ECU: Electronic Control Unit EFI: Electronic Fuel Injection EFP: Electronic Fuel Pump ET: Engine Temperature sensor FI: Fuel Injectors FPR: Fuel Pressure Regulator H-DSSS: Harley-Davidson® Smart Security System HCU: Hydraulic Control Unit, ABS HFSM: Hands Free Security Module HO2S: Heated Oxygen Sensor IAC: Idle Air Control actuator IAT: Intake Air Temperature sensor ICM: Ignition Control Module IMAP: MAP + IAT in one unit ISS: Ion Sensing System JSS: Jiffy Stand Sensor LHCM: Left Hand Control Module MAP: Manifold Absolute Pressure sensor MHR: Right Hand Control Module RCM: Reverse Control Module TCA: Throttle Control Actuator TGS: Twist Grip Sensor TMAP: Intake Air Temperature / Manifold Absolute Pressure equipment TPS: Throttle Position Sensor TSM / TSSM: (Turn Signal / Turn Signal Security Module) VE: Volume Efficiency VIN: Vehicle Identification Number VSS: Vehicle Speed Sensor WSS: Wheel Speed Sensor
These abbreviations, and the accompanying list of trouble codes, can be a great start when your Triumph check engine light comes on. As mentioned above, if you are not comfortable with electrical diagnostic work, a dealership or qualified technician can offer assistance. Please keep in mind that even though you have the ability to clear a DTC using the onboard diagnostic feature, you shouldn't clear the code prior to your service appointment. Let the technician view and clear the codes as they troubleshoot the issue.
Triumph and logo are registered trademarks of Triumph. We are fan of MOTORCYCLES ! We love them.